Download
 Share
 Print this page
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Stereo System
  5. DC-D27
  6. Instruction manual

Listening To The Radio - Sanyo DC-D27 Instruction Manual

Hide thumbs

Advertisement

Table of Contents
LISTENING TO THE RADIO
To turn the unit on and listen to the last received station, press the
BAND button.
Manual tuning
1.
Press the BAND button to select FM or AM.
"TUNER"
is selected
automatically.
"TUNE
appears
on the
display, then "TUNE" is replaced by the tuner mode display.
2.
Press the "+" or "-" TUNING button continuously
until you are close
to the desired
frequency,
then press it briefly
until the desired
frequency is displayed. Each time the button is pressed, the frequency
changes in 0.05 MHz steps for FM and 9 kHz steps for AM.
FM 103.25
MHz
•E
,234
5878
'31 1112
1111
To preset stations
Up to 16 stations in each band (FM and AM) can be preset
1.
Tune in the station to be preset as described in "Manual tuning".
2.
Press the MEMORY button.
103.25
MHz
——
\l/
,,,4
m;:;,;
,111
3.
Press the '{+" or "-" PRESET button to select the channel number to
be preset.
9103.25
m+.
\l/
M
m=:::;
,,
4.
Press the MEMORY button.
In this example,"1 03.25 MHz" FM station is preset on FM channel
number 9.
The number buttons on the remote control can be used for preset
the station. In this example, press O, then 9 after the step 2 above.
FM 103.25
Mtiz
Wil
1234
5878
9
*II
1,,
,
5.
Note:
If the next step is not taken within 10 seconds while performing steps
2-4,
"PROG."
disappears
and the preset operation
is cancelled.
Press the MEMORY button to continue.
Repeat the steps above to add more preset stations.
When presetting
a new station, the previously preset station on the
same channel number of the same band is cleared.
The preset stations will be retained in the memory even if the unit is
turned off.
If the memory
contents
are lost due to a power failure or other
condition,
preset the stations again.
Listening to preset stations
1.
Press the BAND button to select FM or AM.
2.
Press the "+" or "-" PRESET
button to select the desired channel
number. The selected channel number blinks on the display.
-
The number buttons on the remote control can also be used.
Press two number buttons within 4 seconds.
-
To receive an FM stereo broadcast,
make sure that "MONO
is not
displayed. If "MONO" appears, press the FM MODE button to turn the
"MONO
indication off.
"ST" appears when an FM stereo broadcast is received.
If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to monaural reception. ("ST" is
replaced by "MONO
in the display.)
Changing
the AM reception
frequencies
It is not necessary to perform this procedure in the Australia and New Zealand.
1.
Press the BAND button to select "AM".
2.
While pressing the MEMORY button on the front panel, press the STOP button
on the front panel.
522-1710
kHz (9 kHz steps) —
520-1710
kHz (10 kHz steps)
LISTENING TO VIDEO SOURCES
1.
Select "VIDEO.
"VIDEO
appears on the display.
2.
Follow the instructions
supplied with the video equipment.
-9-

Advertisement

Table of Contents
loading

  Also See for Sanyo DC-D27

Sanyo DC-D27 Service Manual
Sanyo DC-D27 Service Manual 45 pages
Sanyo DC-D27 Service Manual
Sanyo DC-D27 Service Manual 44 pages

  Related Manuals for Sanyo DC-D27

  Related Content for Sanyo DC-D27