Warning System Table - Panasonic AG-HPG10P Operating Instructions Manual

Warning system table

When trouble is detected immediately after the power is turned on or during operation, the user is alerted
by the power lamp and beep sound (provided that "ON" is selected as the "BEEP SOUND" setting on the
"OTHER FUNCTIONS" screen (Page 82)).
Type of LCD monitor screen
Priority
warning
SYSTEM ERROR
Cause displayed ∗
1 System error
blinks in red.
P2 card
TURN POWER OFF
2 ejection
Blinks in red.
trouble
LOW BATTERY
Blinks in red. Blinks with
the remaining battery
Low battery
3 display empty. (This
charge
display appears even
when it has been set to
OFF on the setting menu.)
FULL
P2
Blinks in red (display
4 P2 card full
appears only for 3
seconds when [REC] is
pressed).
REC WARNING
Recording
Cause displayed ∗
5
trouble
blinks in red.
Connection
error in PC
6 None
mode at
1394 HOST.
One block on the
remaining battery
Near low display is blinking. (This
7 battery display appears even
charge when it has been set
to OFF on the setting
menu.)
P2 card Remaining media
8
nearly full memory display blinks.
∗
1 P2 SYSTEM ERROR Cause display
• P2 MICON ERROR: P2 microprocessor does not respond.
• P2 CONTROL ERROR: Trouble has occurred in the P2 recording control.
• REC RAM OVERFLOW: Recording RAM overflow
∗
2 REC WARNING Cause display
• CARD ERROR ∗ : P2 card trouble (slot number of trouble card is displayed in
• REC RAM OVERFLOW: Recording RAM overflow
• ERROR: Other recording trouble
∗
3 The warning is cleared when any one of the following operations is performed.
• When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed
• When the PC mode is selected while [THUMBNAIL/MODE] is held down for more than 2 seconds
• When a P2 card has been ejected or another card has been inserted
∗
4 The warning is cleared when any one of the following operations is performed.
• When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed
• When a P2 card has been ejected
Power lamp
display
Blinks at a
1 , rate of 4 times
per second.
Blinks at a
rate of 4 times
per second.
Blinks at a
rate of once
per second.
Blinks at
a rate of 4
times per
second upon
completion of
recording.
Blinks at a
2 , rate of 4 times
per second.
Blinks at a
rate of 4 times
per second.
Blinks at a
rate of once
per second.
Blinks at a
rate of once a
second during
recording.
Warning description and
Beep sound
record/playback operation
P2 microprocessor or
Beeps
control trouble. Operation
continuously.
is stopped.
Trouble has occurred in the
internal memory because a
Beeps P2 card was ejected while
continuously. its data was being accessed.
Both access LEDs blink in
orange (4 Hz).
The battery charge is low.
Recording or playback
Beeps
stops. If the voltage falls
continuously.
further, the power is
automatically turned off.
Beeps
There is no more free
continuously
memory left on the P2
upon
card. Recording is
completion of
stopped ∗
3 .
recording.
Beeps
intermittently
Recording trouble.
at a rate of
Recording is stopped ∗
4 times per
second.
The 1394 cable has been
disconnected or a multiple
number of units have been
None
connected. (Ordinary PC
mode operations can be
performed.)
The battery charge is
None falling to low. Operation is
continued.
Under 2 minutes of
memory remaining on
the P2 card (remaining
None memory display shows
less than one minute).
This warning appears only
during recording.
Action to be taken
Check the cause
display ∗
1 , and consult
your vendor.
Turn off the power.
If something is wrong
with the clips on the
ejected P2 card, repair
them.
Replace the battery.
Delete the unnecessary
clips or insert a new
card.
Turn off the power and turn
it back on. Then check
the recording/playback.
4
. Replace the P2 card
if recording cannot be
performed properly.
Connect the hard drive
as specified in the
procedure concerned.
Replace the battery as
necessary.
Replace the P2 card
or add another card as
necessary.
∗
)
85