Angle Adjustable Speedloader Caster Mount; Adjusting The Angle; Replacing Glide Forks - Standard And Slipstream Single-Sided - TiLite TRA AERO T Owner's Manual

CHAPTER 11: CASTERS AND FORKS
Replacing Glide Forks - Standard and Slipstream Single-
Sided
Tools Needed:
• Two 1/8" Allen Wrenches
• 9/16" Open End Wrench
1. Remove the casters. See "Glide Forks - Standard
Forks – Replacing Casters" on page 11-5 or "Slipstream
Single-Sided Forks – Replacing Casters" on page 11-2.
2. Remove the Allen screws from the fork pivot and push
out the pivot axle. See Figure 11-9.
3. Separate the two halves of the Glide fork.
4. Using the Open End wrench, loosen and remove the
locknut and washer from the fork stem. Slide the fork
pivot and caster cap off of the fork stem. Slide the
caster cap and replacement fork pivot onto the fork
stem and holding the parts in place, slide the washer
onto the fork stem and tighten the locknut.
5. Push firmly on the two halves of the Glide fork with the
elastomer in place, aligning the holes of the fork pivot
with the fork. Insert the pivot axle, reinstall the Allen
screws and securely tighten.
6. Reinstall the casters. See "Glide Forks -
Standard Forks – Replacing Casters" on page 11-5 or
"Slipstream Single-Sided Forks – Replacing Casters"
on page 11-2.

ANGLE ADJUSTABLE SPEEDLOADER CASTER MOUNT

Adjusting the Angle

Tools Needed:
• 5/32" Allen Wrench
• 3/16" Allen Wrench
• Drafting Angle
1. Place the chair on a level surface.
2. Using the 5/32" Allen Wrench, remove Allen screw 1 (outer screw) and the washer. See Figures 11-10 to 11-12.
3. Using the 3/16" Allen wrench, loosen but do not remove Allen screw 2 (center screw) enough to allow the end cap
tabs to slide out of the tab slots.
4. Using a drafting triangle or similar 90° angle tool as shown in Figure 11-13, rotate the fork until the flat edge of the
fork is perpendicular to the level surface.
5. While holding the fork in place, and with the end cap tabs engaged in the tab slots, check to see if one of the
six perimeter holes in the caster end cap aligns with one of the three threaded holes in the caster mount. If so,
proceed to Step 7. If not, proceed to Step 6.
6. Pull the caster end cap away from the caster housing and rotate the caster end cap one-sixth turn and re-engage
the caster end cap tabs in the tab slots. Again, check to see if one of the six perimeter holes in the caster end cap
aligns with one of the three threaded holes in the caster mount. If so, proceed to Step 7. If not, repeat this Step 6
using the next combination of caster end cap tabs and tab slots.
7. Thread Allen screw 1 through the two aligned parts and loosely tighten.
Note: There are six perimeter holes in the caster end cap and three threaded holes in the caster mount. These
are designed to permit 17° of adjustment in 1° increments.
8. Securely tighten the center screw.
Aero T/TRA Owner's Manual
Replacing Glide Forks
Fork Pivot
Pivot Axle
Washer
Locknut
Allen
Screw
C Spring
Axle
Washer
Phillips Screw
Spacer
11-6
Figure 11-9
Fork Stem
Caster Cap
Allen Screw
Elastomer
Fork
Phillips Screw
C Spring
Washer
Spacer
OM_Aero T_TRA_0414RevB