Firmware Update Using The Usb Memory - Sony CBK-HD01 Maintenance Manual

Professional disc camcorder; hd/sd sdi input board; analog composite input board
Table of Contents

Advertisement

1-11-2. Firmware Update Using the USB
Memory
When the firmware update is performed, all types of
firmware are updated.
There are two methods of upgrading the firmware. One is
the method by using the USB memory and the other is the
method by accessing the XDCAM website. This section
describes the method by using the USB memory.
For the method of accessing the XDCAM website, refer to
"2-4-1. Software Update".
For the method of upgrading by using the USB memory,
the USB memory*
1
in which the firmware package file of
the latest version is saved is required.
For the firmware package file, please contact your local
Sony Sales Office/Service Center.
m
• *1: A general USB memory used for PCs can be used.
But when the USB memory is connected to the USB
connector, if the screen shows "Unknown USB", or the
message screen shows "NO USB MEMORY" during the
update, the connected USB memory may have a problem
or it may be misrecognized as an unsupported device. In
such a case, connect another USB memory and try again.
• It takes about 20 minutes to complete the update.
• When the USB memory*
the USB memory*
1
may be damaged. Make sure not to
remove the USB memory*
• Do not turn off the power during the update.
• When a disc is inserted, eject it.
• Set the VDR SW in the inside panel to "STBY".
• If the update fails while the LABY update is in progress,
picture and character may not be displayed in some
cases. In such case, repeat update by following the
procedure described below.
1. If a memory stick is inserted, remove it and insert a
USB memory*
1
that contains the package file (exten-
sion: pkg) in its root directory.
2. While pressing the REC START button and the
MENU knob at the same time, turn ON the power.
3. Wait approximately 30 seconds after power-on. Then,
the tally changes from the flashing at 4 Hz to the flashing
at 1 Hz. (Flashing indicates that update is in progress.)
It takes approximately 20 minutes until the update is
complete.
4. The tally changes from flashing to lighting.
(It indicates that update is complete.)
5. Turn OFF the power and reboot the Camcorder. It
boots up with new version.
PDW-700/V1 (E)
1
is removed during the update,
1
during the update.
1. Copy the firmware package file (extension: pkg) to the
USB memory*
1
of the root and plug it into the USB
connector of the unit.
2. Move the arrow to the DIAGNOSIS category page
named "ROM VERSION 1", and press and hold the
MENU knob.
"SEARCHING PACKAGE FILE" blinks about 10
seconds.
D03 ROM VERSION 1
SEARCHING PACKAGE FILE
PACKAGE: 1.00
SY1
: 1.00
SY2K
: 1.00
SY2U
: 1.00
DRV
: 1.00
AT
: 1.00
FP
: 1.00
3. When the firmware package file exists in the root, the
following display appears.
D03 ROM VERSION 1
PACKAGE: 1.00
SY1
: 1.00
SY2K
: 1.00
SY2U
: 1.00
DRV
: 1.00
AT
: 1.00
FP
: 1.00
4. Press the MENU knob while the arrow is pointing at
"PACKAGE".
5. The YES/NO confirmation menu appears.
PACKAGE UPDATE
VERSION UP OK? YES
CURRENT
VERSION
1.00
UPDATING
Total time : --:--
6. When YES is selected, the firmware update starts.
During the firmware update, the tally blinks at 1 Hz.
"UPDATING" indicates the firmware being updated,
and "Total time" indicates the elapsed time.
PACKAGE UPDATE
CURRENT
VERSION
1.00
UPDATING
Total time : 00:00
TOP
TOP
1.10
NO
NEW
VERSION
1.10
: ----
NEW
VERSION
1.10
: SY1
1-49

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cbk-sc02Pdw-700Pdw-f800

Table of Contents