Panasonic KX-VC300 User Manual page 120

Contacts and Settings
–
"Local site name"
–
"IP Address" (when "Manual" is
selected for "IP Address")
–
"Subnet mask" (when "Manual" is
selected for "IP Address")
•
If you are currently entering "Local site
name", the next screen will not be
displayed even if you press [R].
•
In IP mode, you cannot configure the
"Encryption Key (SIP)" setting. This
setting is available only in NAT Traversal
mode.
For details, refer to the following web site:
http://panasonic.net/psn/products/hdvc/
nat_traversal/index.html
"Connection mode": Press [Enter] and use [
[ ] to select a connection mode (IP Mode or NAT
Traversal Mode).
Note
•
If a connection mode is selected without
completing network settings, the settings
cannot be saved. Before making local site
settings, change the connection mode
(Page 108) and make network settings
(Page 91).
"Local site name": Enter a name for the local site.
"Max. Bandwidth": Press [Enter] and use [
[ ] to select the maximum allowed bandwidth to
be used (512 kbps, 768 kbps, 1.0 Mbps,
1.2 Mbps, 1.5 Mbps, 2.0 Mbps, 2.5 Mbps,
3.0 Mbps, 3.5 Mbps, 4.0 Mbps, 4.5 Mbps,
5.0 Mbps, 5.5 Mbps, 6.0 Mbps, 6.5 Mbps,
7.0 Mbps, 7.5 Mbps, 8.0 Mbps, 8.5 Mbps,
9.0 Mbps, 10.0 Mbps).
Note
•
The maximum bandwidth during a video
conference call adjusts to that of the party
that has set the lowest bandwidth for the
maximum bandwidth setting among all
participating parties.
•
You cannot select a value that is higher than
the maximum bandwidth set by the dealer.
For details, contact your dealer.
•
When you make a 3-party video conference
call, select a value of "1.0 Mbps" or higher.
Otherwise, the image quality and the sound
quality cannot be guaranteed.
•
When you make a 4-party video conference
call, select a value of "1.5 Mbps" or higher.
Otherwise, the image quality and the sound
quality cannot be guaranteed.
120 User Manual
"Encryption (SIP)"/"Encryption (H.323)": Use
[ ][ ] to select whether to enable encryption.
–
"ON": Encryption is enabled.
–
"OFF": Encryption is disabled.
Note
•
Be careful when changing encryption
settings because doing so may cause you
to become unable to communicate with
other parties.
•
Be aware that if encryption is disabled,
eavesdropping might be possible on
networks that are not secured against such
actions.
•
If you cannot specify a value for
"Encryption (SIP)"/"Encryption (H.323)"
]
because the setting is unavailable, contact
your network administrator.
•
"Encryption (H.323)" can be set only in IP
mode.
"Video Quality": Use [
prioritising smooth movement or image quality for
video.
–
"Motion": Prioritise smooth movement.
–
"Sharpness": Prioritise image quality.
Note
•
If you are using the KX-VC300,
]
"Sharpness" can only be selected after
purchasing an activation key card
(KX-VCS401) to enable sending images in
Full HD resolution (Page 115).
•
If one of the other parties is using a software
version older than 2.30 (not including 2.30),
"Motion" will be selected.
•
If "Max Resolution" is set to "HD", and
"Video Quality" is changed from
"Motion" to "Sharpness", the setting for
"Max Resolution" is automatically
changed to "Auto".
•
The value that you select here does not
influence the unit's operation when you
connect to an MCU or non-Panasonic video
conference system.
"Max Resolution": Press [Enter] and use [
[ ] to select the maximum display resolution of the
main video camera and sub video camera used
during a video conference call.
– "Full HD": Maximum resolution: 1920 ´ 1080
(This mode switches the display resolution
according to the condition of the network.)
– "HD": Maximum resolution: 1280 ´ 720
][ ] to select between
]