Konica Minolta 7020 Service Manual page 170

HOME
ADJUSTMENT 25
*1 : FS107 stapling upper limit
Mode
50 sheets
45 sheets
40 sheets
35 sheets
The following dipswitch settings are related:
• DIP SW 2 – 5
1-shot message display at automatic staple mode
clearing.
*2 : FS107 limit on number of stapled sets
If this bit is set to "1", then if the user specifies more
than 25 stapled sets the copier automatically stops
after reaching the 25th set, and displays a message
instructing the user to remove the paper and press
the START button.
*3 : Toner-replenish stop timing
When the TLD (toner level detector) detects that the
toner-out condition has persisted for a fixed length of
time, the copier waits an additional number of copies
(as specified by DIP SW4 – 0, 4 – 1) and then
displays a message instructing the user to load new
toner. (The toner-low condition)
• Toner-level detect (message requesting new toner)
Mode
After 0 effective copies
After 100 effective copies
After 200 effective copies
After 500 effective copies
Following the message display, the copier allows
printing of an additional number of copies as set by
DIP SW4 – 2, 4 – 3, and will then disable copying.
• Count from appearance of toner supply message
until copying is inhibited
Mode
After almost 100 copies
After almost 400 copies
After almost 700 copies
After almost 1000 copies
However, that the copier will stop only if DIP SW4 – 5
("Job stop or nonstop at no toner ") is set to "1".
• The toner-low/toner-out condition is cleared by
1-3 1-4
0 0
1 0
0 1
1 1
4-0 4-1
0 0
1 0
0 1
1 1
4-2 4-3
0 0
1 0
0 1
1 1
4-12
insertion of a new toner bottle (toner-bottle detect
sensor OFF/ON).
• The toner-out stop conditions vary according to
the settings of DIP SW3 – 2 and DIP SW2 – 0.
*4 : 1-shot message display at automatic staple mode
clearing
If 1-shot display is enabled: If the copy limit is exceed
during staple-mode operation, a message indicating
this appears on the display, and copying continues in
sort mode.
Note that this setting is related to the "1-SHOT
DISPLAY TIME" setting available under key-operator
mode. For information about memory switches, refer
to the Instruction Manual.
*5 : F34/F35/F36 latch
In the event of a fixing-related error, the setting
changes to "1" so that power OFF/ON will not clear
the error condition. After correcting (repairing) the
problem, reset this to "0" to re-enable copying.
*6 : Return to EKC screen after copying reservation
If EKC setup is enabled, then if this bit is set to "1"
(return to screen) the copier will immediately display
the EKC password-request screen following exit of
the final sheet for the reserved jobs. If copying is not
reserved, the copier will wait 1 minute following job
completion before displaying the EKC password-
request screen.
*7 : Bypass feed nonstandard size selection
This setting determines whether the system detects
the size of the paper in the bypass tray. If the setting
1
is "1" (handle as nonstandard size), the size is not
detected and copying is based on the maximum
paper size.
*8 : Non-display of advance/delete buttons for job list
Under default conditions, the job list screen allows for
deletion or priority changing of jobs that have been
1
stored in E-RDH memory.
If this bit is set to "1"(non-display), however, the
advance and delete buttons will not appear on the
display so that it will not be possible to delete or
reorder the reserved jobs.