Konica Minolta 7020 Service Manual page 169

HOME
DIP SW
BIT
No.
0
1
2
3
DIP SW23
4
5
6
7
0
1
3
2
3
4
DIP SW24
5
6
7
0
1
2
DIP SW25
3
4
5
6
7
0
1
DIP SW26 2
3
4
5
3
6
7
0
1
2
3
DIP SW27
3
4
5
6
7
Functions
Automatic tray changeover when FNS tray
is full
100 sheets are exited when FNS is
not stapled, and tray is detected full
100 sheets are exited when FNS is
stapled, and tray is detected full
–
Stopping of the machine when the
fixing web counter
Toner density selection of developer
(7020/25/30/35)
Automatic change of printer paper size
Sets tray at commencement of search when
APS is used.
Changeover of original quantity display during
operation
Job start and changeover without print
process stop
Automatic changeover of tray when the
IT101 tray is full
–
–
–
For postcard-to-postcard copying, rotation
takes place even when APS/AMS is not used
180 degree rotation takes place even when
there are no staples
FAX transmission 8K/16K for machines
destined for Taiwan
Printer density selection
(Patch detection control threshold value change)
Image position reference use for by-pass feed
copying on non-standard size paper
Printer EKC mismatch print operation
Top & bottom erase mode of the application
functions (7020/25/30/35)
The timer for canceling a job that was interrupted
due to removal of the key counter is valid
"No IP scanner function" setting
Automatic copying reservation function
(Other than 7020/25/30/35)
–
–
–
–
Density setting when the printer toner save
function is selected (Other than 7020/25/
30/35)
0
No automatic changeover to
Tray 1
No automatic changeover to
Tray 2
No automatic changeover to
Tray 3
No automatic changeover to
Tray 4
No
No
–
Not stop
No
*41
*29
*38
Job No. indication
Without process stop
*36
No automatic changeover to
Tray 1
No automatic changeover to
Tray 2
–
–
–
No rotation
No rotation
Image is transmitted in reduced
form.
*39
Center
Permit
No
Invalid
Use
*42
–
–
–
–
*43
4-11
1
Japan
1
Automatic changeover to
Tray 1
Automatic changeover to
1
Tray 2
Automatic changeover to
1
Tray 3
Automatic changeover to
1
Tray 4
0
Yes
1
Yes
0
–
0
Stops
Set. (Note, however that the bit is
0
automatically made 0 after L detection
adjustment has ended normally.)
0
0
0
0
0
0
Original quantity indication
0
Process stop
0
Automatic changeover to
Tray 1
0
Automatic changeover to
Tray 2
0
–
0
–
– 0
0
Rotation takes place.
0
Rotation takes place.
Image is transmitted with both 0
edges erased.
0
0
1
0
Recording paper side
0
Prohibit
0
Yes
0
Valid
0
Do not use
0
0
–
0
–
0
–
0
–
0
0
0
25 ADJUSTMENT
Default values
Inch Metric
1 1
1 1
1 1
1 1
0 0
1 1
0 0
0 0
0 0
0 0
0 0
0 0
0
1
0 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
1 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0