Konica Minolta 7020 Service Manual page 167

HOME
Note: Parenthesized bit numbers among the initial values apply to the 7022/7130.
3
DIP SW
BIT
No.
0
1
2
3
4
DIP SW13
5
6
3
7
0
1
2
3
DIP SW14
4
5
6
7
0
1
2
3
DIP SW15 4
5
6
3
7
0
1
3
2
3
DIP SW16
4
3
5
6
7
0
1
2
3
DIP SW17
4
5
6
7
0
1
2
DIP SW18
3
4
5
6
7
Functions
–
–
–
Selection of filter for jagged edges on slanting lines
–
–
Threshold for automatic erasure of outside original
(7020/25/30)
Operation when stapling is not possible
(Other than B6R, post card nonstandard)
–
–
Operation when one position stapling is not
available
Operation when two position stapling is not
available
–
–
–
–
–
–
Full stack stop when FNS not installed
Occurrence of overload stop when FNS or IT is
not connected
Fixing temperature at low power mode
Operation of PTC
* In the case of the 7022/7130, the internal
heater is treated as an option.
Copy inhibit flag prior to L detection
Indication to prepare toner bottle
(7020/25/30/35)
Operation when temperature inside machine rises
(7020/25/30)
MPC correction control
F4 size setting
Host printing cannot be performed when a
key counter is installed.
–
Shift from by-pass feed in ATS mode is inhibited.
ITU (inner tray), vendor switchover
Separation claw operation OFF mode
(for machines destined for China)
Unit isolation (1)
0
–
–
–
ON
–
–
*25
Note 1: Initial value for a machine other than the 7020/25/30
in the case where ( ) is appended to the bit No. of the initial value
*26
–
–
*27
*28
–
–
–
–
–
–
No
Decide with DIP SW15-6
*30
Note 2: Initial value for a machine other than the 7035 in the
case where ( ) is appended to the bit No. of the initial value
Always ON
Copy enabel
Not indicated
Stop job
*31
*32
Printing takes place.
–
Shift inhibited.
ITU selected.
Normal
Tray 1 (main body upper)
*33
can be used
Tray 2 (main body lower)
can be used
–
–
Tray 3 (DB upper) can be used
Tray 4 (DB lower) can be used
–
DB can be used
4-9
1
Japan
–
0
–
0
–
0
OFF 0
– 0
–
0
0 (1)
0
0
0
– 0
– 0
0
0
0
0
– 0
– 0
–
0
–
0
–
0
–
0
Machine pauses after 100 sheets
0
have been exited.
Machine pauses after 400 sheets
0
have been exited.
0
1
PTC is OFF if OFF mode, if SW2
0
Note 3
(sub power) is OFF, or if system is
(1)
OFF due to WT or auto shutoff.
Copy inhibit 0
Indicated 0
Stop job, and turn OFF fixing heater 0
0
0
0
0
0
Printer abort processing 0
0
–
0
Shift possible.
0
Vender selected.
0
OFF
0
Tray 1 (main body upper)
is isolated
0
Tray 2 (main body lower)
is isolated
0
–
0
–
0
Tray 3 (DB upper) is isolated
0
Tray 4 (DB lower) is isolated
0
–
0
DB is isolated
25 ADJUSTMENT
Default values
Inch Metric
0 0
0 0
0 0
0 0
0 0
0 0
0 (1) 0 (1)
0 0
1 0
1 0
1 0
1 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
1(0) 1(0)
0 0
(1) (1)
0 0
0 0
0 0
0
0
0 0
0 0
0 0
0 0
0
0
0 0
0
0
0
0
0 0
0
0
0
0
0
0
0
0
0 0
0
0
0
0
0
0