Panasonic UF-490 Service Manual page 121

No. Parameter
017 TX START
018 RX START
019 ITU-T V.34
020 ITU-T ECM
021 EP TONE
022 SIGNAL
INTERVAL
023 TCF CHECK
024 CED
FREQUENCY
025 COMM. START-
UP
026 NON-
STANDARD
027 SHORT
PROTOCOL B
028 SHORT
PROTOCOL D
029 REMOTE
DIAGNOSTICS
030 CED & 300 bps
031 RTC = EOLx12
Function Parameter Table
Selections
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = Off
2 = On
3 = Select
1 = Off (Invalid)
2 = On (Valid)
1 = Off (without EP Tone)
2 = On (with EP Tone)
1 = 100 ms
2 = 200 ms
3 = 500 ms
1 = Normal (Short)
2 = Long
1 = 1080 Hz (non ITU-T)
2 = 2100 Hz
1 = 1'st response
2 = 2'nd response
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (will not accept)
2 = On (accepts)
1 = 75 ms
2 = 1 sec
1 = Off (EOLx6)
2 = On (EOLx12)
Selects the transmission modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when
communicating with regular G3 machines. When
communicating with Super G3 (V.34) machines,
use Parameter No. 32.
Selects the reception modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when
communicating with regular G3 machines. When
communicating with Super G3 (V.34) machines,
use Parameter No. 33.
Selects whether the ITU-T V.34 is Off, On or Select.
Select: Select whether the ITU-T V.34 is Off or On,
when entering Phone Book Dialing Numbers
or Manual Number Dialing.
Select the ECM mode.
Selects whether to add the echo protect tone on V.29
mode.
(Used when Echo Suppression is disabled.)
On : Add
Off : Do not add
Selects the time interval between the receiving signal
and the transmitting signal.
Selects the TCF check interval Long/Short
Selects the CED frequency 2100/1080 Hz
Selects the communication start-up condition (XMT
and Polling).
(Used when Echo Suppression is disabled.)
Selects own mode (Panafax mode).
Selects the short protocol mode.
Selects the short protocol mode. When activated, it
allows the machine to automatically store the modem
speed for each Auto Dial Number.
Selects whether the machine accepts Remote
Diagnostics from the service station.
Selects the pause interval between the CED and the
300 bps signal.
(Used when Echo Suppression is disabled.)
Selects the RTC signal, EOLx6 or EOLx12.
121
Function