Central Machinery 67595 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Saw
  5. 67595
  6. Set up and operating instructions manual

Central Machinery 67595 Set Up And Operating Instructions Manual

14” four speed woodworking bandsaw
Hide thumbs
Table of Contents

Advertisement

Quick Links

WoodWorking BandSaW
Set up and operating inStructionS
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
Copyright
2009 by Harbor Freight Tools
©
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Dia-
grams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may
differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10k
14" Four Speed
Model
Visit our website at: http://www.harborfreight.com
. All rights reserved. No portion of this manual or any artwork contained
®
67595

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 67595

Summary of Contents for Central Machinery 67595

  • Page 1 14” Four Speed WoodWorking BandSaW Model 67595 Set up and operating inStructionS Visit our website at: http://www.harborfreight.com read this material before using this product. Failure to do so can result in serious injury. SaVe thiS Manual. Copyright 2009 by Harbor Freight Tools .

  • Page 2: Table Of Contents

    ........17 phaSe 8: Saw Blade installation..18 Saw Blade tensioning and tracking ........20 guide and Bearing adjustment ..21 SettingS ........23 Blade guide adjustment .....23 table angle adjustment ......23 SKU 67595 For technical questions, please call 1-800-444-3353. Page 2...

  • Page 3: Important Safety Information

    USE RIGHT TOOL. Don’t force tool or injury. attachment to do a job for which it was not designed. notice is used to address practices not related to personal injury. SKU 67595 For technical questions, please call 1-800-444-3353. Page 3...

  • Page 4: Bandsaw Safety Warnings

    Manual Before Operating Saw. hands to operate tool. Wear ANSI-approved eye protection. DON’T OVERREACH. Keep proper foot- Do not remove jammed cutoff pieces ing and balance at all times. until blade has stopped. SKU 67595 For technical questions, please call 1-800-444-3353. Page 4...
  • Page 5 Code § 25249.5, et seq.) People with pacemakers should consult The warnings, precautions, and instruc- their physician(s) before use. Electro- tions discussed in this instruction manual magnetic fields in close proximity to SKU 67595 For technical questions, please call 1-800-444-3353. Page 5...

  • Page 6: Vibration Safety

    To reduce vibration, maintain the tool as explained in this manual. If any abnor- SKU 67595 For technical questions, please call 1-800-444-3353. Page 6...
  • Page 7 125 V~ 3-prong plug and outlet. The outlet must be properly installed and grounded in accordance with all codes and ordinances. Do not use an adapter to connect this tool to a different outlet. SKU 67595 For technical questions, please call 1-800-444-3353. Page 7...

  • Page 8: Specifications

    M6 x 12 Bolt M5 x 15 Pan Head Bolt M8 Washer 1,2,3 M8 Lock Washer 2,3,5 M8 Nut 1,2,3,5 M6 Washer M5 Washer M5 Nut Foot Assembly Pulley Cover Knob Foot Bracket SKU 67595 For technical questions, please call 1-800-444-3353. Page 8...

  • Page 9: Assembly

    Assemble the Rear Panel (2A) to the ing secured with a Washer (H) and Nut Mounting Plate (1A) in the same way. (K). The Stand should look like the illustration above (Figure 1-2). SKU 67595 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 Plate (1A) toward the rear as shown Insert a Foot Assembly (O) through each above (Figure 1-4). Foot Bracket (Q) and Panel (3A, 2A). Secure with Washer (H) and Nut (K). SKU 67595 For technical questions, please call 1-800-444-3353. Page 10...

  • Page 11: Phase 2: Bandsaw Body To Stand Assembly

    Mounting Plate (1A) ing slots, as shown above. is level. Then, wrench tighten all Nuts from phase 1 securely. SKU 67595 For technical questions, please call 1-800-444-3353. Page 11...

  • Page 12: Phase 3: Motor To Stand Assembly

    The Pulley will need to be held in position for now. letter description (for this phase) M8 x 25 Bolt M8 Washer M8 Lock Washer M8 Nut SKU 67595 For technical questions, please call 1-800-444-3353. Page 12...

  • Page 13: Motor Mounting

    Power Cord (14A) during shipment. Motor Mounting Have an assistant hold the Motor (11A) in place while it is attached to the Motor Plate (10A). SKU 67595 For technical questions, please call 1-800-444-3353. Page 13...

  • Page 14: Phase 4: Motor Wiring

    (ground) Motor terMinal Black (hot) Motor terMinal Motor cord The power cord wires are already con- nected at the top connections (black “hot“ wire, white “neutral” wire, and green SKU 67595 For technical questions, please call 1-800-444-3353. Page 14...

  • Page 15: Phase 5: Table Assembly

    Table Bracket (132B) as Bolt (A). Install the Table Stop Bolt into shown above. Secure the Bolts in place the hole noted in the figure above. using Knobs (131B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 15...

  • Page 16: Phase 6: Pulley Cover Assembly And Belt Installation

    Bolt (F) and Washer (L) from the other side. do not overtighten. Close the Pulley Cover door temporarily to make sure it closes completely and securely. REV 10k SKU 67595 For technical questions, please call 1-800-444-3353. Page 16...

  • Page 17: Side Panel Installation

    Side Panel (38A). Assemble the Upper Blade Guard (24B) to the Upper Support Bracket Post (10B) as shown above using the two Hex Head Bolts (26B) and Flat Washers (25B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 17...

  • Page 18: Phase 8: Saw Blade Installation

    Fully open the Upper Front Cover (66B) and the Lower Front Cover (94B) . Figure For Step 8-2 taBle inSert (123B) taBle pin (125B) Remove the Table Insert (123B) and Table Pin (125B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 18...
  • Page 19 Table (122B). Place the Saw Blade (56B) on the Lower Pulley (90B) and through the Lower Blade Guides (117B). Replace the Table Insert (123B) and Table Pin (125B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 19...

  • Page 20: Saw Blade Tensioning And Tracking

    Lower Front Cover (94B) using the ment. Bolts (111B) as shown above. Loosen the Nut (47B) on the shaft of the Blade Tracking Knob (48B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 20...

  • Page 21: Guide And Bearing Adjustment

    Saw Blade without touching it. Then, tighten the Thumb Screws. Loosen the Thumb Screw (17B) and ad- just the Bearing (13B) to 1/64” (0.4mm) behind the Saw Blade. Then, tighten the Thumb Screws. SKU 67595 For technical questions, please call 1-800-444-3353. Page 21...
  • Page 22 18. Tighten the Bolts (119B) after adjustment. Return the Table (122B) to its normal po- sition and secure with the Knobs (131B) Pivot the Table (122B) backward as far as possible. SKU 67595 For technical questions, please call 1-800-444-3353. Page 22...

  • Page 23: Settings

    Then, securely tighten the Knob (6B). Tilt the Table (122B) to the left or right until the Needle points to the desired angle on the Scale (126B). Then, se- curely tighten both Knobs (131B). SKU 67595 For technical questions, please call 1-800-444-3353. Page 23...

  • Page 24: Blade Speed Adjustment

    To turn off power to the bandsaw, push the switch down. Safety Switch When not in use, remove the Key and store in a safe place out of reach of chil- dren. SKU 67595 For technical questions, please call 1-800-444-3353. Page 24...

  • Page 25: Operation

    Move the material slowly and steadily against the Saw Blade. Avoid twisting the Saw Blade when at- tempting to turn sharp corners. Remem- ber to saw around corners. SKU 67595 For technical questions, please call 1-800-444-3353. Page 25...

  • Page 26: Maintenance And Servicing

    You may use a mild detergent. Bad blade. Replace blade. Once clean, lubricate all moving parts with a light oil. When storing, keep the Bandsaw cov- ered with a cloth cover. SKU 67595 For technical questions, please call 1-800-444-3353. Page 26...
  • Page 27 REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE- MENT PARTS THERETO. note: Some parts are listed and shown on the following pages for illustration purposes only, and are not available individually as replacement parts. SKU 67595 For technical questions, please call 1-800-444-3353. Page 27...

  • Page 28: Assembly Diagrams And Parts Lists

    M8 x Ø18 Switch Lock Washer Switch Cover Star Washer Power Cord Switch Plate Strain Relief Side Panel Pulley Cover Relief Stop Pulley Cover Knob ST Screw M3.5 x 12 SKU 67595 For technical questions, please call 1-800-444-3353. Page 28...

  • Page 29: Assembly Diagram A - Stand

    - Stand note: When ordering parts from Assembly Diagram A, include the suffix “A” after the part number. SKU 67595 For technical questions, please call 1-800-444-3353. Page 29...

  • Page 30: Parts List B - Saw Body

    M8 x 30 Pan Head Bolt M5 x 12 138B Spring Washer Clip 139B Brush Wheel Knob 140B Pan Head Bolt M5 x 12 Star Washer (Internal) 146B Miter Gauge Set Base SKU 67595 For technical questions, please call 1-800-444-3353. Page 30...

  • Page 31: Assembly Diagram B - Saw Body

    B - Saw Body note: When ordering parts from Assembly Diagram B, include the suffix “B” after the part number. SKU 67595 For technical questions, please call 1-800-444-3353. Page 31...

  • Page 32: Parts List C - Riser Block Kit (Sold Separately)

    Blade Guard (L) Blade Guard note: check with the harbor Freight parts department for availability. When ordering parts from Assembly Diagram C, include the suffix “C” after the part number. SKU 67595 For technical questions, please call 1-800-444-3353. Page 32...

  • Page 33: Assembly Diagram And Parts List D - Four Speed Pulleys

    Hex Head Bolt M8 x 25 Motor Pulley V-Belt Set Screw M6 x 10 note: When ordering parts from Assembly Diagram D, include the suffix “D” after the part number. SKU 67595 For technical questions, please call 1-800-444-3353. Page 33...

  • Page 34: Limited 1 Year / 90 Day Warranty

    liMited 1 Year / 90 daY WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.

Table of Contents