List Of Valid Commands (Which Can Be Used In Conjunction With The Execute Command); List Of Valid Variables - NetComm NTC-6000 SERIES User Manual

"set VARIABLE=`VALUE`"
"get VARIABLE"
A password (if required), only needs to be specified once per SMS, but can be prefixed to each command if desired.
"PASSWORD get Variable1"; "get VARABLE2"
"PASSWORD set VARIABLE1=VALUE1"; "set VARIABLE2=VALUE2"
If the command sent includes the "reboot" command and has already passed the White List password check, the device keeps this
password and executes the remaining command line after the reboot with this same password.
For Example:
"PASSWORD execute reboot; get Variable1"; "get VARABLE2"
"PASSWORD execute reboot; PASSWORD get Variable1"; "get VARABLE2"
Commands are case insensitive, however variable names and values are case sensitive
9.10 List of valid commands (which can be used in conjunction with
the execute command):
"pdpcycle", "pdpdown" and "pdpup" commands can have a profile number suffix 'x' added. Without the suffix specified, the command
operates against the current active profile or last active profile.
# Command name
1 reboot
2 pdpcycle or pdpcyclex
3 pdpdown or pdpdownx
4 pdpup or pdpupx

9.11 List of valid variables:

Where "x" is a profile number (1-6). If no profile is specified, variables are read or written to for the current active profile. If a profile is
specified, variable are read or written to for the specified profile number ('x').
# RDB variable name
0 link.profile.x.enable
link.profile.x.apn
link.profile.x.user
link.profile.x.pass
link.profile.x.auth_type
link.profile.x.iplocal
link.profile.x.status
1 link.profile.x.apn
2 link.profile.x.user
3 link.profile.x.pass
4 link.profile.x.auth_type
5 link.profile.x.iplocal
6 wwan.0.radio.information.
signal_strength
7 wwan.0.imei
8 statistics.usage_current
9 statistics.usage_current
10 /proc/uptime
11 wwan.0.system_network_
status.current_band
YML6000
www.netcomm.com.au
NetComm CallDirect™ Series - NTC-6000 Series
Description
Immediately perform a soft reboot
Disconnect (if connected) and reconnect the 3G connection. If a profile number is selected in the command,
try to disconnect/reconnect the specified profile in case the profile is active. If no profile number is selected, try
to disconnect/reconnect the current active profile. Reports an error if no profile number is selected and there
is no currently activated profile.
Disconnect the PDP. If a profile number is selected in the command, try to disconnect the specified profile in
case the profile is active. If no profile number is selected, try to disconnect the current active profile. Reports
an error if no profile number is selected and there is no currently activated profile.
Reconnect the PDP. If a profile number is selected in the command, try to connect with the specified profile.
If no profile number is selected, try to connect to the last active profile. The router will check the currently
activated profile and disconnect this profile before executing the command. Reports an error if no profile
number is selected and there is no stored last active profile number.
SMS variable name Read/Write Description
profile or profilex RW Profile
apn or apnx RW APN
username or usernamex RW 3G username
password or password RW 3G password
authtype or authtypex RW 3G Authentication type
wanip or wanipx R WAN IP address
rssi R 3G signal strength
imei R IMEI number
usage R 3G data usage of current session
wanuptime R Up time of current 3G session
deviceuptime R Device up time
band R Current 3G frequency
Example
Read: (profile no,apn,user,pass,auth,iplocal,status)
1,Telstra.internet,username,password,
chap,202.44.185.111,up
Write: (apn, user, pass,auth)
Telstra.internet,username,password
telstra.internet
Guest, could also return "null"
Guest, could also return "null"
"pap" or"chap"
202.44.185.111
65 dBm
359102128941027512
"Rx 500 bytes, Tx 1024 bytes, Total 1524 bytes" or "Rx 0
byte, Tx 0 byte, Total 0 byte" when wwan down
1 days 02:30:12 or 0 days 00:00:00 when wwan down
1 days 02:30:12
WCDMA 850
NTC-6000 User Guide
45