26. RS-485 Site Communication
This table is used to set the Communication Parameters between the Data Boards installed in the Matrix Switcher and the Camera
Site..
S e t
U p
R S - 4 8 5
S i t e C o m m u n i c a t i o n
D a i s y
C a m e r a I n
N u m b e r
# 1
0 2
# 2
0 4
# 3
0 6
# 4
# 5
1 0
# 6
# 7
# 8
W h e n D a i s y M o d e i s " o n " o n l y # 1 w i l l b e a v a i l a b l e
F 1 : - -
1. Move the cursor to the 3 position by moving the Joystick Controller.
Enter the desired data board number, 1-8, by pressing the Numeric Key, then press the Set (SET) Key.
2. Move the cursor to the 4 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select Daisy-Chain connection (On) or Home Run Connection (Off)
by moving the Joystick Controller and then pressing the Set (SET) Key to execute the selection.
3. Move the cursor to the 5 position by moving the Joystick Controller.
Enter the desired camera number for site communication by pressing the Numeric Keys and then pressing the Set (SET) Key
to execute the selection.
4. Move the cursor to the 6 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select Full or Half Duplex by moving the Joystick Controller and then
pressing the Set (SET) Key to execute the selection.
5. Move the cursor to the 7 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Delay Time by moving the Joystick Controller and
then pressing the Set (SET) Key to execute the selection.
6. Move the cursor to the 8 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Baud Rate by moving the Joystick Controller and
then pressing the Set (SET) Key to execute the selection.
7. Move the cursor to the 9 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Wait Time by moving the Joystick Controller and
then pressing the Set (SET) Key to execute the selection.
8. Repeat the above procedures until the table is completed.
9. When all settings are completed, press the Escape (ESC) Key to escape from the programming mode. The cursor returns to
the 3 position.
S y s t e m
R S - 4 8 5
O f f
F / H
D e l a y
B a u d
D u p l e x
T i m e
R a t e
F u l l
O f f
1 9 2 0 0
H a l f
O f f
9 6 0 0
1 0 0
1 9 2 0 0
F u l l
F u l l
O f f
1 9 2 0 0
F u l l
O f f
1 2 0 0
F u l l
O f f
1 9 2 0 0
F u l l
O f f
1 9 2 0 0
O f f
1 9 2 0 0
F u l l
F 2 : - -
-89-
B o a r d A d d r .
1
W a i t
D a t a
P a r i t y
T i m e
B i t
C h e c k
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
O f f
8
N o n e
F 3 : D E L
F 4 : P o p
U p
S t o p
B i t
1
1
1
1
1
1
1
1
5