Advertisement
Available languages
Available languages
Option
2:
Top vented
modeHs
with
a custom
full front
panel
NOTE:
The
handHe for the custom
paneH is not incHuded.
IMPORTANT:
Hf the handHe is attached
from
the back of the
custom
panel
the screw
heads
must
be flush
with
the
panel
Hf the handHe
is attached
to the front
of the custom
paneH, the screw
Hengths
cannot
exceed
the paneH
thickness.
For more
information
on KitchenAid
custom
handHe
seHecfion,
refer
to the KitchenAid
CataHog,
visit
www.Mtchenaid.com,
or call 1-800-422-1230_
NOTE:
A custom
full front
paneH must
weigh
no more
than
16 pounds
(7_3 kg) and must
be made
to specific
dimensions.
Ht is recommended
that
a cabinetmaker
cut the
custom
panel
because
of the precise
dimensions
needed.
NOTE:
All mounting
hardware
supplied
are for a 3/4"
(19.1 ram)
thick
wood
panel.
If a thinner
wood
panel,
or
materials
other
than
wood
are used,
it is the consumer's
responsibility
to obtain
the proper
length
screws
and
adjust
the pilot
holes
accordingl%
IMPORTANT:
Use a moisture
resistant
sealer
on both
sides
and all edges
of the panel
to protect
it from
humidity.
23-1/2" (59,7cm)
m
_30-3/16" (76,7 cm)
custom pane!
dimensions
/
3/4" (19.1 ram)
_This dimension
is for 4" (10.2 cm) toe kick. If the installation
needs a higher toe kick, adiust the height of the wood
panel
accordingly,
Not recommended
for toe kicks greater than 6"
(15,2 cm).
1. Remove the inner panel from the door,
2. With aTORX <_) screwdriver,
remove three screws from
both sides of the door,
3. Hold the inner panel up while removing
the screws,
4. Gently set panel aside.
NOTE: Some models have four screws per side,
3 screws
3 screws
inner door
panel
5. Lay the custom
full front
panel
face
down
on a
protective,
non-scratching
surface.
6. Measure
9-29/32"
(25.2 cm) from
top of panel
and mark
a line on the back of panel.
(25,2 cm)
mark line
7. Place the inner
panel
on the back of the custom
panel
so
that the top holes
in the inner
panel
are on the line, and
the panels
are centered
side to side.
8. Mark
all 4 holes,
remove
inner
panel
and drill 3/32"
pilot
holes
1/2" (13 ram)
deep.
mark pilot holes
9. Place
the inner
panel
on the back of the custom
panel
as shovvn_
10. Attach
with
the four
#10-16
x 3/8" hex head
screws
from
the literature
package.
11. Attach
the handle.The
handle
should
be centered
on
the front
of the custom
panel
in the area shown.
_MPORTANT:
Screw
heads
must
be flush
with
back of
custom
panel.
(15,2 cm)
12.
13.
14.
15.
Attach
the custom
panel,
inner
panel,
and handle
assembly
to the door.
Reinstall
the two
upper
most
screws
into the inner
panel,
do not tighten
completely.This
will
hold
the
custom
panel
assembly
in place
on the door
frame.
Align
the top edge
of the custom
panel
with
the top of
the console.
Mark two holes on the custom panel through
the holes
in the upper corners of the inner panel and console, as
shown,
mark through
these holes
12
Advertisement
