Hold Quick Spin Step; Fast Time Down Test; Quick Service Cycle; Membrane Pad Test - Maytag Neptune TL FAV6800A Service

Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing
requires power.
4) Spin to index speed 350 rpm and hold for 6 seconds.
5) Spin to index speed 550 rpm and hold for 6 seconds.
6) Spin to index speed 700 rpm and hold for 6 seconds.
7) Spin to index speed 850 rpm and hold for 6 seconds.
Pump out.
8) Coast down to 0 rpm chimes 3 times.
Speed Range Displayed
a) 0-99 rpm 0-99 (actual)
b) 100-999 rpm Speed X 10 ex: 85.= 850rpm

Hold Quick Spin Step

If the Hand Wash key is pressed again during
the Quick Spin test, the machine will hold at the
next highest index speed for up to 30 minutes.
To cancel press the Hand Wash key again.

Fast Time Down Test

¾
While any test or cycle is running in Service
Mode, pressing the Quick Wash key will
advance the program to the next cycle
stage.
For example if in one of the following:
Stage of
Advances To
Wash Cycle
End of Presoak
Presoak
Every 5 Minutes of
Wash
Wash Time
End of the
Spin/Drain
Spin Profile
Rinse End of Rinse

Quick Service Cycle

@
While in Service Mode, pressing the
Wash/Rinse Temp key will start a Quick
Service Cycle. This will be a quick check of all
systems. If display shows od then open and close lid.
Pressing Quick Wash will advance to the next cycle.
The following steps are performed: Display shows "sc".
1. Lock lid and pump starts.
2. Cold bleach fill. Energize the cold and bleach water
valves to low setting. Advance to next step if water is
not connected to machine.
3. Tumble using 48 rpm tumble for 10 seconds.
4. Tumble with hot fill: Continue tumble while energizing
hot water valve for 5 seconds.
©2003 Maytag Appliances Company
!
WARNING
5. Warm softener fill: Energize cold water and fabric
softener valves until medium level is reached.
Advance to next step if water is not connected to
machine.
6. Drain and Spin to 850 rpm.
7. Display a "PA" (Passed) continuously for 5 seconds
if no diagnostic codes were logged during the test.
8. Unlock the lid when the RPM is zero.
If a diagnostic code is logged during the test, the right-
most dot will turn on and stay on until quick service cycle
test has ended. Any diagnostic code logged during this
test will result in failure of the test, but will not necessarily
stop the test.
During the Quick Service Cycle, pressing the Quick
while the system is suspended or on hold.

Membrane Pad Test

While in Service Mode, pressing the Presoak key will
start a membrane switch check that verifies switch
operation. All the LEDs (except Presoak ) can be toggled
or slewed by pressing the key associated with the LED or
set of LEDs. Each time either set delay arrow is pressed
the digits toggle between a blank and
(including the OFF button) must be pressed within 5
minutes for this test to pass. "PA" will be displayed for
five (5) seconds once all keys have been pressed and the
test is completed. Following 10 seconds of inactivity at
any point, this test will exit without any display.

Motor Control Board Output Test

1. Disconnect power to the washer.
2. Remove the front panel and disconnect the JP4
Connector from the Motor Control Board.
3. Reconnect the washer power cord to supply voltage.
Make sure the lid is closed.
4. Press Enviro Plus and Spin Only keys for 3
seconds to activate Service Mode.
5. Access Board Output Test by pressing the
Delicates key. Display shows "ot".
6. The lid must be locked to access Motor Control
Board Output Test. To lock the lid press
Colors/Jeans. To verify the test, the quick wash LED
will be on, indicating the system relay is activated. If
off, press Quick Wash with the lid shut to activate.
7. Press Whites to start the motor control output test.
This will send 120VAC to the motor control board.
The motor control will execute a test routine and the
motor should run, rotating the spinner at 50 rpm.
There could be up to a 20 second delay before the
spinner starts rotating.
16022808 Rev. 0
Wash key will advance to the next step.
Pressing the Hand Wash key will suspend
the machine at the current step for up to 30
minutes or until Hand Wash is pressed
again. All LEDs should flash on and off
8
. All keys
15