Advertisement
Quick Links
Top Load Washer⎯Technical Information
FAV6800A*, FAV7500A*
• Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or
repair of this unit.
• Refer to Service Manual 16022808 for detailed installation, operating, testing, troubleshooting, and disassembly
instructions.
All safety information must be followed as provided in Service Manual 16022808.
To avoid risk of electrical shock, personal injury or death; disconnect power before servicing, unless
testing requires power.
©2005 Maytag Services
!
CAUTION
!
WARNING
1
16023155
Advertisement
Related Manuals for Maytag FAV6800A Series
Summary of Contents for Maytag FAV6800A Series
- Page 1 • Refer to Service Manual 16022808 for detailed installation, operating, testing, troubleshooting, and disassembly instructions. CAUTION All safety information must be followed as provided in Service Manual 16022808. WARNING To avoid risk of electrical shock, personal injury or death; disconnect power before servicing, unless testing requires power. ©2005 Maytag Services 16023155...
-
Page 2: Normal
Check Tub Displacement Sensor connection and • Perform Motor and Motor Control Test . main harness connector at machine control • Washer does not tumble during most fills or board. during presoak. • Washer with heat option does not tumble while 16023155 ©2005 Maytag Services... -
Page 3: Troubleshooting
Push lid closed to Go to No Fill Test make sure nothing from the inside is • Check for 120 VAC at the pump when a spin cycle pressing against the lid, preventing is selected < 550 rpm. unlocking. ©2005 Maytag Services 16023155... -
Page 4: Super Wash
Service Mode can be entered in the middle Board Press Super Press Super of any wash cycle without interrupting the cycle. Wash Wash Input While in Service Mode, the technician can cancel the Test current cycle, set a continuous running mode, start a 16023155 ©2005 Maytag Services... -
Page 5: Delicates
If display shows od then open and 2) Spin to index speed 90 rpm and hold for 60 close lid. Pressing Quick Wash will advance to the seconds. Pump drains machine. next cycle. ©2005 Maytag Services 16023155... -
Page 6: Enviro Plus
Illustration. If motor windings are good, replace 2. Remove the front panel and disconnect the JP4 the motor control board. Connector from the Motor Control Board. 3. Reconnect the washer power cord to supply voltage. Make sure the lid is closed. 16023155 ©2005 Maytag Services... -
Page 7: Extra Rinse
The first time the Set Delay Time down 3. For “Low Water Level” start a Enviro Plus cycle. arrow key is pushed, the newest code will be After water fill stop cycle and enter “ Board ©2005 Maytag Services 16023155... - Page 8 Customer may have Output Test" after the last three tried to repeat wash completed completed cycle without wash cycles. cycles. opening the lid. Go to "Lid Lock Test" 16023155 ©2005 Maytag Services...
-
Page 9: Start/Pause
Control Board if a diagnostic code 28 has been logged in a cycle. connector. See “Wrong Water Temperature” in the trouble shooting tips, at the beginning of this document for more information. ©2005 Maytag Services 16023155... - Page 10 Pressure 1 and 9 GY/BK 0 to 20 Switch High Ohms (no 1. Enter the Service Mode by pressing and holding Level YL/BL water in the Enviro Plus and Spin Only keys for three machine) seconds. 16023155 ©2005 Maytag Services...
- Page 11 Closed when not processor satisfied Medium water level 0 - 12 VDC Digital Input to Micro- Closed when not processor satisfied High water level 120 VAC Input to Micro- Closed when not processor and some satisfied relays ©2005 Maytag Services 16023155...
-
Page 12: Table Of Contents
Note: When the Neptune TL is plugged in, the Machine Control Board will check the lid latch mechanism every 20 seconds. If found to be locked with no cycle running, the Control Board will send a signal to the switch to unlock the lid. 16023155 ©2005 Maytag Services... - Page 13 Wiring Schematic WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to before servicing, unless testing requires it. ©2005 Maytag Services 16023155...