Away Indicator 6; Operation Of Codepads In Partitioning; 20. Domestic Dialling; Acknowledging Domestic Calls - Bosch ICP-CC488 User Manual

ICP-CC488 | User's Guide | 20.
PARTIAL Indicator
Only displays when an area is armed in STAY Mode
1. (For example, if the PARTIAL indicator is
displayed, an area is armed in STAY Mode 1. If the
PARTIAL indicator is not displayed, no areas are
armed in STAY Mode 1.)
19.2 Operation of Codepads in
Partitioning
Area Addressable Codepad Operations
If you have a system partitioned with Area
Addressable eight-zone codepads, the operating
procedure is the same as described for a non-
partitioned system, except that all operations only
relate to the area the codepad is assigned to.
Master Partitioned Codepad Operations
If your system is partitioned with a Master
Partitioned codepad installed, the operating
procedure is the same as described for a non-
partitioned system, except that all operations relate to
the area displayed by the Area Display indicator.
Example
If the Area Display indicator displays number 2, all
operations performed only operate in Area 2. To
operate Area 1, you must toggle the Area Display
indicator to number 1 by pressing the [#] key.
Pressing the [#] key again toggles you back to the
Area 2 display.

20. Domestic Dialling

Use domestic dialing can be used to call your mobile
phone or a relative/friend if your control panel
activates an alarm. Up to three different telephone
numbers can be programmed for the control panel to
call when an alarm occurs. Only your installer can
program the system to report in the domestic format.
The Master Code holder can change the telephone
numbers at any time.
20.1

Acknowledging Domestic Calls

When an alarm condition occurs, the system calls the
first programmed telephone number. When you
answer an incoming call, the system repeatedly emits
a siren tone followed by a pause, continuously for 2
min (for example, siren tone, pause, siren tone, and
pause).
If you do not acknowledge the call from the control
panel during a pause between siren tones, the control
panel hangs up after 2 min and calls the next
telephone number.
Pressing the [*] key for 1 sec to 3 sec during the
pause acknowledges the call. No further calls are
made for that event. If the call was successfully
acknowledged, a tone of decreasing pitch sounds.
Bosch Security Systems, Inc. | 12/08 | F01U089456-02
Domestic Dialling

Table 13: Domestic Dialing Telephone Digits

Digit
Required
0
1
2
3
4
5
6
7
20.2
If your system is set up for domestic dialing, any
Master Code holder can program telephone numbers
that the control panel calls in the event of an alarm.
How to Program Telephone Numbers
1. Enter your four character Master Code, followed
by the [2] and [#] keys (for example, [25802#]).
Three beeps sound and the STAY and AWAY
indicators flash.
If there are telephone numbers already
programmed, they display one digit at a time by
the codepad indicators.
If there are no telephone numbers programmed,
two more beeps sound after entering this mode.
These two beeps normally sound after the last
digit of the last telephone number displays.
2. Enter all digits for the first telephone number
(for example, [96721717]).
As each digit is entered, the corresponding
codepad indicators display.
3. If there is more than one telephone number to
program, press [*4]. This inserts a break between
the first telephone number and the sec telephone
number. If there is only one telephone number
to program, press the [#] key to exit from this
function.
4. Enter all the digits of the second telephone
number (for example, [96721055]).
As each digit is entered, the corresponding
codepad indicators display.
5. After the last digit of the second telephone
number is programmed, press the [#] key to exit
from this function unless a third telephone
number is required. If there is a third telephone
number to program, press the [*4] button to
insert a break between the second telephone
number and the third telephone number.
20.3
To cancel domestic dialing (for example, you are
moving and do not want the system to continue
calling your mobile phone), enter the following
sequence.
Number to Digit
Program Required
0 8
1 9
2
3 *
4 #
5 4-sec Pause
6 Break
7
Programming Domestic Telephone
Numbers

Disable Domestic Dialing

EN | 17
Number to
Program
8
9
*1
*2
*3
*4