Exiting The Program Mode - Olivetti ECR 2200 Instructions Manual

NOTE: Program all the desired features at the same time in order to
create a single receipt of all selections. Keep the receipt in a
safe place for future reference.
Making Changes to Cash Register Pr Making Changes to Cash Reg Making Changes to Cash Reg Making Changes to Cash Reg Making Changes to Cash Reg
Once the cash register is programmed to satisfy your specific needs,
there is no need to reprogram the entire machine to make single
program changes or corrections. If you wish to make a change (such as
an update to VAT rates, PLUs or Euro exchange rates), be sure you are
in the program mode, re-do the program in question and finalize when
you are ready to exit the programming mode. A new program entry will
automatically overwrite a previous entry for the same program.
Enter Enter ing the Pr ing the Pr ogram Mode ogram Mode
Enter Enter Entering the Pr ing the Pr ing the Program Mode ogram Mode ogram Mode
To enter into the program mode, unlock, open and remove the printer
compartment cover and then slide the control switch to the PRG
position. Refit the printer compartment cover.

Exiting the Program Mode

Exiting the Pr Exiting the Pr ogram Mode ogram Mode ogram Mode
Exiting the Pr Exiting the Pr ogram Mode
To exit the program mode, open the printer compartment cover and
slide the control switch to the R1 or R2 position if you wish to carry out
sales transactions, to the X or Z position if you wish to take
management reports, or to the OFF position if you wish to exit.
Clear Clearing Err Clear ing Err ing Error or or or ors s s s s ing Err
Clear Clear ing Err
To clear an error made during the programming phase, simply press
the [C] key. The error tone ends, the display clears and the keypad
unlocks.
If the message "SEC Code" is displayed, this means that a PRG and Z
mode security password was programmed. Enter the 4-digit code
followed by the [Charge] key to continue.
ister Programming ister Pr ister Pr ister Pr ogramming ogramming ogramming ogramming
In case an error condition cannot be cleared, perform one of the two
general clearance methods explained in the section entitled General
Clearance. Remember that the second general clearance sets all
counters and totals to zero, and cancels all features programmed.
Cler Cler k Number k Number s and Secr s and Secr
Cler Clerk Number Cler k Numbers and Secr k Number s and Secr s and Secret Codes
Clerk codes are a special security feature to control access to the
register. You can program up to 6 individual clerk numbers linked to
secret entry codes of three digits each.
Pr Pr Pr Pr Programming a Secr ogramming a Secr ogramming a Secr ogramming a Secr ogramming a Secret Code Link et Code Linked to a Cler et Code Link et Code Link et Code Link
Number Number Number Number Number
1. Open the printer compartment and slide the control switch to the
PRG position.
2. Activate the clerk system by typing [44444] followed by [1] and
then pressing the [Amt Tend/TOTAL] key.
3. Type [444444] and press the [Amt Tend/TOTAL] key.
4. Type a number to identify the clerk which the secret code will be
linked.
5. Set a three-digit secret code by typing three [numeric keys].
6. Press the [Clerk] key.
Repeat the above operations (from step 3 to step 6) to assign a secret
code to the remaining 5 Clerks or use the [C] key to exit from Clerk
Secret Code programming.
If you wish to change the clerk's secret code and the Clerk system is
already activated, there is no need to perform step 2 above.
Example: Assign secret code 106 to Clerk 1 for the first time.
Type/Press:
[44444] + [1] + [Amt Tend/TOTAL] + [444444] + [Amt Tend/TOTAL]
+ [1106] + [Clerk]
et Codes et Codes
et Codes et Codes
ed to a Cler ed to a Cler ed to a Clerk k k k k ed to a Cler
15