Table of Contents
Advertisement
Available languages
Available languages
TROUBLESHOOTING
First try the solutions
suggested
here or visit our website
to possibly
avoid the cost of a service
call.
in U.S.A. www, maytag,com/product_help
- in Canada
www, maytag,ca,
If you experience
|
Possible
Causes
_
Solution
J[
[
oL (overloaded)
appears
in display
uL (unbalanced
load)
appears
in display
LF (too long to fill)
appears
in display
Ld (too long to drain
water)
appears
in display
HC (Hot and Cold
hoses reversed)
appears
in display
Sd (Excess suds)
appears
in display
If an overload
is detected,
the washer
will drain any water and
detergent
in the washer.
Remove several
items and add HE
detergent.
Close lid and press START/PAUSE,
Allow the washer
to continue.
If the dial is flashing
and the washer
has stopped,
redistribute
the load, close the lid, and press START/
PAUSE.
Load too large.
Load not balanced.
The washer
is
running
a load-balance
correction
routine.
Washer
taking too long to fill.
Drain extends
more than
4,5" (114 mm) into standpipe.
Washer
taking too long to drain
water. Drain extends
more than
4,5" (114 mm) into standpipe.
Hot and cold inlet hoses have been
installed
incorrectly.
Excessive
suds in washer.
Washer
is
running
a suds reduction
routine.
An item in the load may be keeping
the
lid from locking.
Washer
lid left open.
Objects
on washer
lid prevent
it from
unlocking.
System
error code.
Washer
sets back to factory
default.
Check plumbing
for correct
drain hose installation.
Use drain hose
form and attach securely
to drainpipe
or tub, Do not tape over drain
opening.
See Installation
Instructions.
Check plumbing
for correct
drain hose installation.
Use drain hose
form and attach securely
to drainpipe
or tub, Do not tape over drain
opening.
See Installation
Instructions.
Lower drain hose if the end is higher than 96" (2,4 m) above
the floor. Remove any clogs from drain hose. See Installation
Instructions.
This code will appear at the end of the wash cycle to indicate that
cold water hose is connected
to the hot water inlet and hot water
hose is connected
to the cold water inlet.
dL (Lid cannot
lock)
appears
in display
lid (Lid opened)
Close the lid to clear the display. If the lid is left open for more than
appears
in display
10 minutes,
the cycle will reset and water in the washer
will drain,
dU (Lid cannot unlock)
Remove objects,
such as a basket of laundry, from the top of the
appears
in display
washer.
F##
code (F-type
Press START/PAUSE
once to clear the code. Then press
error code) appears
START/PAUSE
again to restart washer.
If code appears
again,
in display
call for service.
Fd (Factory
Default)
Allow the washer
to continue.
Use only HE detergent.
Always measure
detergent,
and base detergent
quantity
on
load size. Follow detergent
manufacturer's
instructions.
If the dial is
flashing,
reselect
your desired
cycle using a cold wash temperature,
and press START/PAUSE,
Do not add detergent.
Check for items directly
under the lid,
To return all options and modifiers to Factory Default, press
POWER/CANCEL,
select RINSE/DRAIN & SPIN cycle, and then
press EXTRA RINSE, FABRIC SOFTENER, EXTRA RINSE, FABRIC
SOFTENER within 5 seconds. When done correctly, the display
shows "Fd" for 3 seconds and then unit returns to Standby Mode.
ACCESSORIES
See Installation
instructions for installation
accessories
Part
Number:
Accessory
8212526
Washer drip tray, fits under all
31682
All-purpose
appliance cleaner
1903WH
Laundry supply storage cart
19
Advertisement
Table of Contents
