Show View ® Set Up - Philips VR1200/02 User Manual

S
S
E T T I N G E T T I N G
E T T I N G
Clock Setting
You can also reset or correct the clock manually.
1 1 1 1 1 Press VCR.
2 2 2 2 2 Press MENU.
3 3 3 3 3 Press 5 or ∞ to select "INITIAL SET UP "
then press OK/STATUS.
The Initial Set Up menu appears.
4 4 4 4 4 Press 5 or ∞ to select "SET CLOCK" then
press OK/STATUS. The Clock Set screen
appears.
TIME
DATE
SMART CLOCK
CHANNEL
SET : 5∞
END : MENU
5 5 5 5 5 Press 5 or ∞ to set the time, then press OK/
STATUS .
• Each time you press 5 or ∞, the set time
changes by 1-minute intervals. If you hold
the button, the set time changes by
30-minute intervals.
6 6 6 6 6 Press 5 or ∞ to set the date, then press OK/
STATUS.
• Each time you press 5 or ∞, the set date
changes by 1-day intervals. If you hold the
button, the set date changes by 15-day
intervals.
7 7 7 7 7 Press 5 or ∞ to set the year, then press OK/
STATUS.
• Each time you press 5 or ∞, the set year
changes by 1-year intervals. If you hold the
button, the set year changes rapidly.
8 8 8 8 8 Press 5 or ∞ to set the SMART CLOCK
function, then press OK/STATUS. (Except for
MAGYARORSZÁG (36), ˇ CESKÁ REPUB-
LICA (42), POLSKA (48), HJCCBZ (07) or
OTHER EASTERN EUROPEAN (EE)
countries.)
ON: To get accurate time keeping through
automatic adjustments at regular inter-
vals, by reading data from PDC signal.
OFF: If the clock setting data from PDC
signal is incorrrect, set to "OFF".
However, setting to "OFF" reduces the
accuracy of the built-in clock, which
could adversely affect timer recording.
If you set to "ON," press 5 or ∞ to set the
channel position to the station that transmits the
clock setting data, then press OK/STATUS.
9 9 9 9 9 Press MENU to exit. The clock starts to
operate.
U
( C ( C
P P
P ( C
O N T I N U E D O N T I N U E D
O N T I N U E D
– –:– –
01/01/01
ON
1
NEXT : OK
) )
)
Notes:
• Smart Clock (when set to "ON") adjusts the
VCR's built-in clock every hour, except for
23:00, 0:00, 1:00 and 2:00.
• Smart Clock is not effective when ...
– the VCR's power is "ON".
– the VCR is in the Timer mode.
– a difference of more than 3 minutes exists
between the built-in clock's time and the
actual time.
– the VCR is in the Auto Satellite Prog Rec
mode (✈P.38).
– the VCR is in the Power Save mode
(✈P.14).
• If Smart Clock is set to "ON", the VCR's
clock is automatically adjusted at the start/
end of Summer Time.
• Smart Clock may not function properly
depending on the reception condition.
• If a power failure occurs, the clock will lose
its setting.
®
S V
HOW IEW
To ensure that S
operates correctly, it is necessary to set the
"Guide Channel (GUIDE CHANNEL)" number
for each station.
"Guide Channel (GUIDE CH) number" refers
to the assigned TV station numbers, according
to broadcast area, for S
recording. The Guide Channel numbers can
be found in most TV listings.
IMPORTANT
Normally, Auto Set Up (✈P.10), Follow TV
(✈P.12) or Auto Channel Set (✈P.16) sets the
Guide Channel Numbers automatically. You need
to set the Guide Channel Numbers manually only
in the following cases:
a) when timer-programming with S
system, the channel position, where the station
you wish to record is received on your VCR,
is not selected or when you add a channel
after Auto Set Up, Follow TV or Auto
Channel Set has taken place. In this case, set
the Guide Channel Number for that station
manually.
— —
20
Set Up
V Timer Recording
HOW IEW
V timer
HOW IEW
HOW
V
IEW