Clock Setting; Show View ® Set Up - Philips Show View VR1600 User Manual

S
ETTING

Clock Setting

You can also reset or correct the clock
manually.
1
Select Clock Set Screen
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "INITIAL
SET UP" then press OK/STATUS.
The Initial Set Up menu appears.
4 Press 5 or ∞ to select "SET
CLOCK" then press OK/STATUS.
The clock Set screen appears.
TIME 0:00MODE SET
DATE 01/01/00
JUST CLOCK OFF
CHANNEL 1
SET : 5∞
NEXT : OK
END : MENU
2
Set Clock
1 Press 5 or ∞ to set the time, then
press OK/STATUS.
• Each time you press 5 or ∞, the set
time changes by 1-minute intervals.
If you hold the button, the set time
changes by 30-minute intervals.
2 Press 5 or ∞ to set the date, then
press OK/STATUS.
• Each time you press 5 or ∞, the set
date changes by 1-day intervals. If
you hold the button, the set date
changes by 15-day intervals.
3 Press 5 or ∞ to set the year, then
press OK/STATUS.
• Each time you press 5 or ∞, the
set year changes by 1-year
intervals. If you hold the button,
the set year changes rapidly.
4 Except for MAGYARORSZAG (36),
CESKA REPUBLIKA (42),
POLSKA (48) or OTHER EASTERN
EUROPE (EE) country. Press
5 or ∞ to set the JUST CLOCK
function, then press OK/STATUS.
ON: To get accurate time keeping
through automatic adjustments at
regular intervals, by reading data
from PDC signal.
OFF:If the clock setting data from PDC
signal is incorrrect, set to "OFF".
However, setting to "OFF" reduces
the accuracy of the built-in clock,
which could adversely affect timer
recording.
If you set to "ON", press 5 or ∞ to set
the channel position to the station that
transmits the clock setting data, then
press OK/STATUS.
U
P
(C
ONTINUED
3
Finish Setting
Press MENU to exit. The clock starts to
operate.
Notes:
• Just Clock (when set to "ON") adjusts the
VCR's built-in clock every hour, except for
23:00, 0:00, 1:00 and 2:00.
• Just Clock is not effective when . . .
– the VCR's power is "ON".
– the VCR is in the Timer mode.
– a difference of more than 3 minutes
exists between the built-in clock's time
and the actual time.
– the VCR is in the Auto Satellite Prog
Rec mode ( P.33).
– the VCR is in the Power Save mode
( P.16).
• If Just Clock is set to "ON", the VCR's
clock is automatically adjusted at the
start/end of Summer Time.
• Just Clock may not function properly
depending on the reception condition.
• If a power failure occurs, the clock will
lose its setting.
S V
HOW IEW
To ensure that S
Recording operates correctly, it is
necessary to set the "Guide Channel
(GUIDE CH)" number for each station.
"Guide Channel (GUIDE CH)
number" refers to the assigned TV
station numbers, according to
broadcast area, for S
recording. The Guide Channel
numbers can be found in most TV
listings.
IMPORTANT
Normally, Auto Set Up ( P. 12), Follow TV
( P. 14) or Auto Channel Set ( P. 17) sets
the Guide Channel Numbers automatically.
You need to set the Guide Channel Numbers
manually only in the following cases.
a) When timer-programming with the
S V
HOW IEW
where the station you wish to record is
received on your VCR, is not selected or
when you add a channel after Auto Set
Up, Follow TV or Auto Channel Set has
taken place. In this case, set the Guide
Channel Number for that station
manually.
b) When you delete a channel or change
channel positions manually after Auto
Set Up, Follow TV or Auto Channel Set
has taken place. In this case, set the
Guide Channel Numbers for all the
receivable stations manually.
c) When you wish to timer-record a satellite
programme with the S
In this case, set the Guide Channel
Numbers for all satellite broadcasts
received on your satellite tuner.
)
®
Set Up
V Timer
HOW IEW
V timer
HOW IEW
system, the channel position,
V System.
HOW IEW
— 20 —
1
Select Initial Set Screen
1 Press MENU.
2 Press 5 or ∞ to select "INITIAL
SET UP" then press OK/STATUS.
VCR SET UP
AUTO TUNER SET UP
MANUAL TUNER SET UP
OUTPUT/INPUT SETUPL E
\ INITIAL SET UP
REC LEVEL SET UP
TAPE MANAGER
SELECT : 5∞
CONFIRM : OK
END : MENU
2
Set Guide Channel Number
1 Press 5 or ∞ to select "GUIDE
CHANNEL SET UP" then press
OK/STATUS.
2 Press 5 or ∞ or Number buttons to
enter the
GUIDE CHANNEL SET UP
guide chan-
GUIDE CH
nel number
255
01
( G U I D E
02
CH) then
03
04
press
SELECT: 5 ∞ OR 0-9
O K / S TA -
CONFIRM : OK
TUS.
END : MENU
3 Press 5 or
∞ or Number buttons to enter the
number of the VCR's channel
position (TV PROG) on which the
Guide Channel number's broadcast is
received, then press
OK/STATUS.
GUIDE CHANNEL SET UP
GUIDE CH TV PROG
254 --
255 --
01 01 ARD
02 02 ZDF
03 03
SELECT: 5 ∞ OR 0-9
CONFIRM : OK
END : MENU
4 Repeat the above procedures until
you set the guide channel number for
all the receivable stations.
• If the satellite broadcast is received
on your VCR's auxiliary channel
"L-2", select "A/V2 REAR (or
SAT)" for the channel position.
3
Finish Setting
Press MENU.
TV PROG
--
01 ARD
02 ZDF
03
04