Hitachi L700 SERIES Instruction Manual page 246

Chapter 8 List of Data Settings
Code Function name
A041 Torque boost method selection
Torque boost method selection,
A241
2nd motor
A042 Manual torque boost value
A242 Manual torque boost value, 2nd motor
A342 Manual torque boost value, 3rd motor
Manual torque boost frequency
A043
adjustment
Manual torque boost frequency
A243
adjustment, 2nd motor
Manual torque boost frequency
A343
adjustment, 3rd motor
V/F characteristic curve selection,
A044
1st motor
V/F characteristic curve selection,
A244
2nd motor
V/F characteristic curve selection,
A344
3rd motor
A045 V/f gain setting
Voltage compensation gain setting for
A046
automatic torque boost. 1st motor
Voltage compensation gain setting for
A246
automatic torque boost, 2nd motor
Slippage compensation gain setting for
A047
automatic torque boost, 1st motor
Slippage compensation gain setting for
A247
automatic torque boost, 2nd motor
A051 DC braking enable
A052 DC braking frequency setting
A053 DC braking wait time
A054 DC braking force during deceleration
A055 DC braking time for deceleration
DC braking/edge or level detection for
A056
[DB] input
A057 DC braking force for starting
A058 DC braking time for starting
A059 DC braking carrier frequency setting
A061 Frequency upper limit setting
A261 Frequency upper limit setting, 2nd motor 0.00 or "2nd minimum frequency limit" to "maximum frequency, 2nd motor" (Hz)
A062 Frequency lower limit setting
A262 Frequency lower limit setting, 2nd motor 0.00 or "start frequency" to "maximum frequency, 2nd motor limit"(Hz)
A063 Jump (center) frequency setting 1
Jump (hysteresis) frequency width
A064
setting 1
A065 Jump (center) frequency setting 2
Jump (hysteresis) frequency width
A066
setting 2
A067 Jump (center) frequency setting 3
Jump (hysteresis) frequency width
A068
setting 3
A069 Acceleration stop frequency setting
A070 Acceleration stop time frequency setting 0.0 to 60.0 (s)
A071 PID Function Enable
A072 PID proportional gain
A073 PID integral time constant
A074 PID derivative gain
A075 PV scale conversion
A076 PV source setting
A077 Output of inverted PID deviation
A078 PID variation range
A079 PID feed forward selection
(Note)<>indicate the setting range of 90 to 160kW
Monitored data or setting
00 (manual torque boost), 01 (automatic torque boost)
00 (manual torque boost), 01 (automatic torque boost)
0.0 to 20.0 (%)
0.0 to 20.0 (%)
0.0 to 20.0 (%)
0.0 to 50.0 (%)
0.0 to 50.0 (%)
0.0 to 50.0 (%)
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz-range sensorless vector), 05 (vector with sensor)
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz-range sensorless vector)
00(VC), 01(VP)
20. to 100. (%)
0. to 255.
0. to 255.
0. to 255.
0. to 255.
00 (disabling), 01 (enabling), 02 (set frequency only)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.0 to 5.0 (s)
0. to 70. (%) <0. to 50. (%)>
0.0 to 60.0 (s)
00 (edge operation), 01 (level operation)
0. to 70.(%) <0. to 50. (%)>
0.0 to 60.0(s)
0.5 to 12.0(kHz) <0.5 to 8.0 (kHz) >
0.00 or "1st minimum frequency limit" to "maximum frequency" (Hz)
0.00 or "start frequency" to "maximum frequency limit" (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz)
00 (disabling), 01 (enabling), 02 (enabling inverted-data output)
0.2 to 5.0
0.0 to 999.9, 1000. to 3600. (s)
0.00 to 99.99, 100.0 (s)
0.01 to 99.99
00 (input via OI), 01 (input via O), 02 (external communication), 03 (pulse-string
frequency input), 10 (operation result output)
00(OFF), 01 (ON)
0.0 to 100.0 (%)
00 (disabled), 01 (O input), 02 (OI input), 03 (O2 input)
8 - 4
Setting Change
Default
during during
operation operation Page
(allowed (allowed
_FF
or not) or not)
00
00
1.0
1.0
1.0
4-18
5.0
5.0
5.0
00
00 4-16
00
100. 4-15
100.
100.
4-14
100.
100.
00
0.50
0.0
0.
0.5
4-20
01
0.
0.0
3.0
0.00
0.00
4-24
0.00
0.00
0.00
0.50
0.00
0.50
4-25
0.00
0.50
0.00
0.0
00
1.0
1.0
0.00
1.00
4-26
00
00
0.00
00