Related Manuals for Honeywell UltraKey Touch HJC4000
Summary of Contents for Honeywell UltraKey Touch HJC4000
- Page 1 UltraKey Touch DVR and PTZ Keyboard Controller HJC4000 Installation and User Guide Document 800-06554 – Rev C – 02/11...
- Page 3 Installation and User Guide...
- Page 4 Revisions Issue Date Revisions 08/10 New document. 08/10 Document revised for preproduction release. 02/11 Document updated for latest software changes. Changes include additions to the PTZ keyboard operations section for Diamond and Intellibus protocols. This is the production release version of this document.
-
Page 5: Table Of Contents
UltraKey Touch Installation and User Guide Contents About this Document ..........11 Overview of the Contents. - Page 6 Contents Step 2: Standalone Configuration for DVR Settings ..... . . 40 Step 3A: Configure the Controller for a Serial Port Connection ....41 Step 3B: Configure the Controller IP for an Ethernet Connection .
- Page 7 UltraKey Touch Installation and User Guide Figures Figure 1-1 UltraKey Touch Port Connections ....... 18 Figure 1-2 RJ45 Box Front and Back Ports .
- Page 8 Figures...
- Page 9 UltraKey Touch Installation and User Guide Tables Table 1-1 Shipping Checklist ........17 Table 1-2 UltraKey Touch Specifications .
- Page 10 Tables...
-
Page 11: About This Document
UltraKey Touch Installation and User Guide About this Document In this section: • Overview of the Contents, page 11 • Explanation of Symbols, page 11 • Cautions and Warnings, page 12 • Important Safety Instructions, page 14 • Warranty and Service, page 15 •... -
Page 12: Cautions And Warnings
Caution The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the enclosure of the product that may be of sufficient magnitude to constitute a risk of electric shock to the person. Caution The exclamation point in a yellow equilateral triangle is a Caution. -
Page 13: Fcc Compliance Statement
Users of the product are responsible for checking and complying with all federal, state, and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell shall not be held responsible for the use of this product in violation of current laws and statutes. -
Page 14: Europe
Europe The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 2004/108/EC and the Low Voltage Directive LVD 2006/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety. -
Page 15: Warranty And Service
Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.CCTV for assistance or to request a Return Merchandise... - Page 16 Font What it represents Example Swiss721 BT Bold Words or characters that you must type. The word Enter the password. “enter” is used if you must type text and then press key. Enter Return Menu titles and other items you select Double-click Open from the File menu.
-
Page 17: Ultrakey Touch Overview
UltraKey Touch Overview The UltraKey Touch keyboard controller (HJC4000) is a replacement for the Honeywell HJZTP controller and is compatible with Honeywell DVRs and PTZs. The UltraKey Touch can control the following types of DVRs and PTZs, depending on the type of connection used: •... -
Page 18: Ultrakey Touch Port Connections And Descriptions
UltraKey Touch Overview Table 1-1 Shipping Checklist (cont’d) Quantity Part Use for... RJ45 network cable, 2 meters All installations. RJ45 box RS485 connection requirements. UltraKey Touch Port Connections and Descriptions Figure 1-1 UltraKey Touch Port Connections Power RJ45 Ethernet RS232 and RS485 Serial Port Pins are numbered from left to right DC Power Port Supports 12V (±10%) DC/1 A power input. -
Page 19: Rs232, Rs485 Serial Port
UltraKey Touch Installation and User Guide RS232, RS485 Serial Port Note These ports are used to connect to DVR RS232/485 or PTZ RS485 ports. An isolated surge protector is suggested when using RS485 and when cabling between buildings. RJ45 Box Use the terminal box RJ45 port and 8-pin terminal plug as required for compatibility and connectivity options. -
Page 20: Ultrakey Touch Specifications
UltraKey Touch Overview UltraKey Touch Specifications Table 1-2 UltraKey Touch Specifications Parameter Value Power Requirement 10.8 to 13.2 VDC @ 1 Ampere (A) Connector Types 1 × Ethernet (10Base-T, 100Base-TX) RJ45 with LED 1 × RS232/485 RJ45 with LED Type: STN, Positive Image Backlight: Blue-White Characters: 122 ×... -
Page 21: Using The Ultrakey Touch Controller
Using the UltraKey Touch Controller You may need to learn how to use the UltraKey Touch both before and after you begin configuring. This section covers: • Logging Onto the Controller on page • Using the UltraKey Touch to Navigate the LCD Menus on page Logging Onto the Controller Connect the keyboard with a power adapter (12V [±10%] DC/1 A included). -
Page 22: Figure 2-1 Ultrakey Touch Controller Keyboard Layout
Using the UltraKey Touch Controller Figure 2-1 UltraKey Touch Controller Keyboard Layout Table 2-1 UltraKey Touch Controller Keys and Controls Icon Description Icon Description LCD screen Alarm key Sequence key Iris open / close key Set key Recycle key Backwards key Review key Stop key Search key... - Page 23 UltraKey Touch Installation and User Guide Table 2-1 UltraKey Touch Controller Keys and Controls (cont’d) Icon Description Icon Description Monitor key Camera key Alt key PTZ Call key Touch pad slider Focus near / far key Operations with the touch pad are described in these instructions as “Slider_Direction”.
-
Page 24: Figure 2-2 Ultrakey Touch Navigation Controls
Using the UltraKey Touch Controller Figure 2-2 UltraKey Touch Navigation Controls Touch Pad and Ring Forward key (or up) Touch pad ring Right arrow key Left arrow key Touch pad slider (used Backward or reverse key like a laptop mouse pad) (or down) LCD Keys LCD screen... -
Page 25: Connecting Ultrakey Touch To A Dvr
Connecting UltraKey Touch to a DVR This section covers: • Navigating the LCD Configuration Menus on page • Connect to the UltraKey Touch Using the Serial Port (RS232) on page • Connect to the UltraKey Touch Using the Serial Port (RS485) on page •... -
Page 26: Navigating The Lcd Configuration Menus
Connecting UltraKey Touch to a DVR Navigating the LCD Configuration Menus Figure 3-1 LCD and LCD Navigation Keys Right arrow key Left arrow Up arrow key Down arrow key Numeric keypad and Ent key Figure 3-2 DVR Configuration Menu Tree System Configuration Standalone... -
Page 27: Connect To The Ultrakey Touch Using The Serial Port (Rs232)
UltraKey Touch Installation and User Guide Connect to the UltraKey Touch Using the Serial Port (RS232) Step 1: Connect to the UltraKey Touch Using the Serial Port Table 3-1 Serial Port Com2 (RS232) Pin Assignments Serial Port Type Signal COM2 RS232 Note For a list of cable accessories, see the... -
Page 28: Step 2: Configure The Ultrakey Touch For Dvr Use
Connecting UltraKey Touch to a DVR Figure 3-3 Connecting the Controller for DVR Control RJ45 to DB9F for RS232 NETWORK Network Network Network cable cable cable Serial Port (RS232) Network Port Network Port Master Slave1 UltraKey Touch Step 2: Configure the UltraKey Touch for DVR Use Note Set the DVR type in the Ultrakey Touch configuration to be the same as the connected DVR type. -
Page 29: Step 3: Configure The Ultrakey Touch Serial Port Settings
UltraKey Touch Installation and User Guide Press Ent to enter the DVR Selection menu. Press the DVR Selection Slider_Up/Down to select the DVR to control. Fusion DVR Selection HRDP DVR Selection HRXD Press Ent to enter the Basic Set menu. Press the Basic Set: Slider_Up/Down until the PORT SELECT submenu DVR/CAM... -
Page 30: Connect To The Ultrakey Touch Using The Serial Port (Rs485)
Connecting UltraKey Touch to a DVR Press the Slider_Up/Down or LCD up/down arrow Serial Port: keys to select Com2 (RS232). Press Ent or Com2(RS232) Slider_Right to confirm, and Slider_Left to return. The Serial Setting menu displays. Here you can set the Com2 (RS232) settings for parity, baud rate, data bit and stop bit: Press the Slider_Right to select Parity. -
Page 31: Table 3-4 Rj45 Box Pin Assignments
UltraKey Touch Installation and User Guide Plug the AC adapter into the controller power port and the adapter into a power source. Connect the RJ45 network cable to the serial port of the controller and the RJ45 box. Connect the pins (RS485+, RS485–) of the RJ45 box to the pins (T/R+, T/R–) of the RS232-RS485 converter using appropriate wire. -
Page 32: Step 2: Configure The Ultrakey Touch For Dvr Use
Connecting UltraKey Touch to a DVR Figure 3-4 Connecting the Controller for DVR Control Using RS485 Serial Port (RS232) RS232-RS485 Converter Serial Port (RS485) RJ45 Box NETWORK Network Network Network Cable Cable Cable Serial Port (RS485) Network Port Network Port Master Slave1 UltraKey Touch... -
Page 33: Step 3: Configure The Ultrakey Touch For Serial Port Settings
UltraKey Touch Installation and User Guide Press Login, and enter the password, 1234. This indicates that the This indicates that the keyboard is in PTZ mode. keyboard is in DVR mode. CAM 001 CAM 001 DVR 1 User2 User2 From the home screen, press Alt > Clr to enter the System Configuration System Configuration menu. -
Page 34: Table 3-5 Serial Port Com1 (Rs485) Configurations
Connecting UltraKey Touch to a DVR Table 3-5 Serial Port Com1 (RS485) Configurations Type RS485 Baud Rate 9600 Parity None DataBit StopBit Press Alt > Clr a second time to enter the System Configuration menu. Rotate the slider to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default). -
Page 35: Installing And Configuring An Ethernet Connection
UltraKey Touch Installation and User Guide Installing and Configuring an Ethernet Connection Note DVR ethernet control is currently unavailable. It will be available in future releases. For a list of cable accessories see the Shipping Checklist on page 17, and for port connections and pin assignments, see UltraKey Touch Port Connections and Descriptions on page 18. -
Page 36: Step 2: Configure The Ultrakey Touch For Dvr Use
Connecting UltraKey Touch to a DVR Figure 3-5 Ethernet Port Connections to DVR Network Port Network Cable NETWORK Network Network Network Cable Cable Cable UltraKey Touch Network Port Network Port Network Port Master Slave 1 Slave 2 Step 2: Configure the UltraKey Touch for DVR Use Note If any mode other than DVR has been selected, then use the procedure in Step 2: Configure the UltraKey Touch for DVR Use on page 28... -
Page 37: Keyboard Configuration For Cascade Linkage (Additional)
UltraKey Touch Installation and User Guide Press Slider_Down, the menu displays (one of): Network: Network: Network: DHCP Manual Setting Show Net Infor Select the Network: Manual Setting menu and press Ent to confirm. Press the Slider_Up/Down or the LCD up/down arrow keys to setup the UltraKey Touch network parameters (IP Address, Gateway, NetMask and DNS): Press the Slider_Up/Down or the LCD up/down Network:... - Page 38 Connecting UltraKey Touch to a DVR Note The IP address of the master or slave keyboard is both referred to IP address in the Network menu. Press Alt > Clr and scroll with the slider. The Cascade System Configuration Linkage menu appears. Cascade Linkage In cascade mode, you can set the keyboard status (such as master or slave), and the cascade IP address if its status is set as “slave”.
-
Page 39: Configuring Ultrakey Touch Using The Web Browser (Optional)
UltraKey Touch Installation and User Guide Configuring UltraKey Touch Using the Web Browser (Optional) Logging into the Web Browser Input, navigate to, or copy and paste, the applicable IP address into your web browser: • LAN connections: for example, http://192.168.1.9 (default). •... -
Page 40: Step 2: Standalone Configuration For Dvr Settings
Connecting UltraKey Touch to a DVR Figure 3-7 System Configuration Tab Top menu Side menu Step 2: Standalone Configuration for DVR Settings From the side menu, click Standalone Configuration (see Figure 3-8). Set the DVR type to be the same as the controlled DVR in the DVR Type drop-down list. -
Page 41: Step 3A: Configure The Controller For A Serial Port Connection
UltraKey Touch Installation and User Guide Figure 3-8 Standalone Configuration for DVR Tab Side menu Step 3A: Configure the Controller for a Serial Port Connection From the side menu, click Serial Port Configuration (see Figure 3-9). In the Serial Port1 Settings window area, select the appropriate value in the drop-down lists from each of the following fields: •... -
Page 42: Step 3B: Configure The Controller Ip For An Ethernet Connection
Connecting UltraKey Touch to a DVR Figure 3-9 Serial Port Configuration Tab Side menu Step 3B: Configure the Controller IP for an Ethernet Connection From the side menu, click IP Configuration (see Figure 3-10). Enter IP Address, Subnet Mask, Gateway and DNS values in each of the fields. Click Apply to save the configuration, Cancel to exit without saving, or Default to restore all factory default values. -
Page 43: Controlling A Fusion Dvr
UltraKey Touch Installation and User Guide Figure 3-10 IP Configuration Tab Side menu Controlling a FUSION DVR Step 1: Connection Figure 3-3 page 28, and Figure 3-4 page Step 2: Select DVR Type Press Alt + Clr to enter the Standalone Settings menu. See the menu tree (see Figure 3-2 page 26) to select the DVR. -
Page 44: Step 3: Dvr And Camera Connection
Connecting UltraKey Touch to a DVR Step 3: DVR and Camera Connection Press the Slider_Right to enter the Basic Set menu. Basic Set: DVR/CAM Press Ent. Rotate the slider to select the Camera (from CAM 1 1 to 128). Press the Slider_Right to select the DVR as 1. - Page 45 UltraKey Touch Installation and User Guide Table 3-8 Operating a Fusion DVR You want to... Do this... Auto Sequence Press Seq to toggle Auto Sequence on a Fusion DVR. Toggle Relay (alarm output) on a Press the number key (less than 5), then Alarm. specified channel Instant Record Press the number key, which represents a specific channel, followed by...
-
Page 46: Controlling An Hrxd/Hrsd Dvr
Connecting UltraKey Touch to a DVR Controlling an HRXD/HRSD DVR Step 1: Connection Figure 3-3 page 28, and Figure 3-4 page Step 2: Keyboard Setup for Connection HRXD DVR setup is the same as the FUSION DVR setup DVR Selection: except that you select HRXD (see Controlling a FUSION DVR HRXD... - Page 47 UltraKey Touch Installation and User Guide Table 3-9 Operating an HRXD DVR You want to... Do this... Cycle through the cameras that are displayed Use the Slider_Left/Right. when viewing 2x2 and 3x3 displays Set the screen layout of the multi-cameras, Press Ent, then Slider_Up, Slider_Down, Slider_Left or and select a camera to be displayed in the Slider_Right to select an active camera (highlight box...
-
Page 48: Controlling An Hrdp Dvr
Do this... Zoom in on an image on the screen Press Set. To control PTZ domes Press Alt > Set to enable HJC4000 to control PTZ domes. Note For more information about PTZ operation for HRXD, see Step 2: Camera... - Page 49 UltraKey Touch Installation and User Guide Table 3-10 Operating an HRDP DVR You want to... Do this... Auto Sequence Press Seq to cycle through the remaining channels within the display mode or rotate the display configuration. For both live viewing and searching, in PTZ mode, Seq can be used to enter PRESET mode.
-
Page 50: Table 3-11 Joystick Controls
Connecting UltraKey Touch to a DVR Table 3-10 Operating an HRDP DVR You want to... Do this... To control PTZ cameras Use the joystick or see the table below for the keyboard operations for contolling PTZ domes. Press... To... Press... To... -
Page 51: Installing Ultrakey Touch With Ptz
Installing UltraKey Touch with PTZ This section covers: • Navigating LCD Configuration Menus on page • Installing and Configuring a Serial Connection on page • Configuring UltraKey Touch Using the Web Browser (Optional) on page • Controlling PTZs on page Note For all installations, refer to the applicable PTZ installation or user guides for more information. -
Page 52: Installing And Configuring A Serial Connection
Installing UltraKey Touch with PTZ Figure 4-1 PTZ Configuration Menu Tree System Configuration Standalone Serial Port Network Settings COM1 (RS485) Show Net Infor Manual Settings DHCP PTZ Settings Serial Settings IP Address NetMask Protocol / Baud Rate Data Bit Gateway Address / Name Parity Stop Bit... -
Page 53: Figure 4-2 Rs485 Serial Port Connection Ptz By Rj45 Box
UltraKey Touch Installation and User Guide RS485 Serial Port Connecting to a PTZ using the RJ45 Box: Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Figure 4-2. Connect an RJ45 network cable from the RJ45 Box port to the controller serial port. Connect the pin (RS485+, RS485–) of the RJ45 Box to a PTZ using an appropriate wire. -
Page 54: Step 2: Configure The Controller For Ptz
Installing UltraKey Touch with PTZ Step 2: Configure the Controller for PTZ Note In the Standalone main menu, press Ent, and rotate the slider to enter PTZ settings or press PTZ. You can set the PTZ Name, Address, and Protocol. Install and connect the controller to a power source, if it is not already connected. - Page 55 UltraKey Touch Installation and User Guide Press the Slider_Up/Down or LCD up/down arrow key to scroll through the options (standalone settings, serial port, network, language, slider update, cascade linkage, hardware test, about, and restore default). When you are at the System Configuration: Serial Port menu, press Ent. System Configuration: Serial Port Serial Port...
-
Page 56: Configuring Ultrakey Touch Using The Web Browser (Optional)
Installing UltraKey Touch with PTZ Configuring UltraKey Touch Using the Web Browser (Optional) Logging into the Web Browser If not already done, navigate to, or copy and paste, the applicable IP address into your web browser: • LAN connections: for example, the default IP is http://192.168.1.9. •... -
Page 57: Step 2: Standalone Configuration For Ptz Settings
UltraKey Touch Installation and User Guide Figure 4-4 System Configuration Tab Step 2: Standalone Configuration for PTZ Settings From the side menu, click Standalone Configuration (see Figure 4-5). Under DVR Setting drop-down list, set DVR type as same as the controlled DVR. Under Cascade Mode, the settings are used for cascading linkage of keyboards. -
Page 58: Step 3: Configure The Controller For A Serial Port Connection
Installing UltraKey Touch with PTZ Figure 4-5 Standalone Configuration for PTZ Tab Step 3: Configure the Controller for a Serial Port Connection From the side menu, click Serial Port Configuration (see Figure 4-6). Under Serial Com1 Settings, select the following from each drop-down list, as required: •... -
Page 59: Controlling Ptzs
UltraKey Touch Installation and User Guide Figure 4-6 Serial Port Configuration Tab Controlling PTZs Step 1: Keyboard Setup For a connection between Ultrakey Touch and a PTZ, see Figure 4-2. Certain settings should be done before using the direct control of PTZ with Ultrakey Touch. Set COM1 (RS485) according to the table below: Type RS485... -
Page 60: Step 2: Camera Selection
Installing UltraKey Touch with PTZ See the PTZ configuration menu tree ( Figure 4-1 Standalone Set: page 52). Select Standalone Settings, press Ent, and rotate the slider to enter PTZ Settings, or press PTZ. You can set the PTZ Name, Address, and Protocol. Note The UltraKey Touch supports five PTZ Protocols: Pelco P, Pelco D, Diamond, VCL, and Intellibus. - Page 61 UltraKey Touch Installation and User Guide PTZ - Tour <Cam001> Press Ent, enter a tour number, and then press Ent Tour again. Press the LCD Up/Down arrow keys to toggle between selections in the Program/Run/Cancel/Delete function submenu. Press Ent to confirm the selection. PTZ - Preshot Menu <Cam001>...
- Page 62 Installing UltraKey Touch with PTZ PTZ call for Intellibus Protocol Familiarize yourself with these basic operations before you start configuring the menus: • Press Ent to enter the setup menu and the submenus displayed on the LCD screen. Press the number on the keyboard to select a submenu, then press Ent to confirm the selection.
- Page 63 UltraKey Touch Installation and User Guide PTZ – VectorScan Once <Cam 001> Press PTZ call, select the VectorScan Once submenu VectorScan Once and press Ent. PTZ – Preset List <Cam 001> Press PTZ call and Preset List is displayed on the LCD Preset List screen.
- Page 64 Installing UltraKey Touch with PTZ...
-
Page 65: System Administration And Troubleshooting
System Administration and Troubleshooting This section covers: • System Administration Using the Controller LCD on page • System Administration Using the Web Browser on page System Administration Using the Controller LCD To navigate all configuration LCD menus, see the System Configuration Menu Tree page 75. -
Page 66: Restore Default
System Administration and Troubleshooting Restore Default Log into the controller. From the System Configuration menu, press System Configuration Slider_Up/Down to scroll to Restore default. Restore default Press Ent to confirm whether or not to restore to factory defaults. Updating the Touch Pad Firmware Log into the controller. -
Page 67: System Administration Using The Web Browser
UltraKey Touch Installation and User Guide Press Slider_Up/Down keys and press Ent to select one or all of the following test options: • Key: When you press a key, the key value and its Device Test: state is displayed on LCD. •... -
Page 68: Rebooting Ultrakey Touch
System Administration and Troubleshooting The Upgrade Status window opens. Messages display to indicate when old files are being erased and new files are being copied. When the process is complete, the message Upgrade success displays and the system reboots. Figure 5-1 Software Upgrade Warning Message Rebooting UltraKey Touch Log into the web browser. -
Page 69: Figure 5-2 Change Password Page
UltraKey Touch Installation and User Guide Figure 5-2 Change Password Page Document 800-06554 Rev C 02/11... - Page 70 System Administration and Troubleshooting...
-
Page 71: Appendix Advr Operation Commands
DVR Operation Commands Fusion Operation Commands Table A-1 Fusion DVR Operations Keys... Function... Number keys Press a number key + DVR, or DVR + number + Ent to select a DVR to control. Press 4+1 + Split to display in 4A grid Press 4+2 + Split to display in 4B grid Press 4+3 + Split to display in 4C grid Press 4+4 + Split to display in 4D grid... -
Page 72: Hrxd/Hrsd Operation Commands
DVR Operation Commands Table A-1 Fusion DVR Operations (cont’d) Keys... Function... Touch Pad Slider Adjusts the forward and backward playback speeds. Search Press to display the Search menu for configuring the date, month, and time for playback. F2, F7, F6, F8, Ent, Clr Up, down, left, right, confirm, esc Press F3 to display video of the previously selected camera. -
Page 73: Hrdp Operation Commands
Press to make DVR playback quickly. Backward Press to make DVR rewind quickly. Press to zoom the image on the screen. PTZ Control Press Alt+Set to enable HJC4000 to control PTZ of HRXD/HRSD. HRDP Operation Commands Table A-3 HRDP Operations Keys... - Page 74 DVR Operation Commands Table A-3 HRDP Operations (cont’d) Keys... Function... Monitor Press to enter the DVR Setup menu. Reverse/F6 Press to play recorded videos in reverse. Continuously pressing Reverse will change the playback speed. Stop Not supported. Forward/F8 Press to play recorded videos. Continuously pressing Forward will change the playback speed.
-
Page 75: System Configuration Menu Tree
UltraKey Touch Installation and User Guide System Configuration Menu Tree Figure A-1 System Configuration LCD Menu Tree - All Modes Show Net Infor IP Address NetMask Network Manual Settings Gateway DHCP Slider Update Slider Hardware Test Serial Port Joystick IP Address Cascade Linkage KBD Mode... - Page 76 DVR Operation Commands...
- Page 78 Document 800-06554 – Rev C – 02/11 © 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof.