Settings - Denon AVR-890 Owner's Manual

ENGLISH
Setting items
Channel Level Test Tone Start : Output test tones.
FL (Front L)/ C (Center)/ FR (Front R)/ SR (Surround R)/
Set the volume of the test
SBR z (Surround Back R)/ SBL z (Surround Back L)/ SL (Surround L)/
tone to be the same when it
FHL (Front Height L)/ FHR (Front Height R)/ SW (Subwoofer) : Select
is output from each speaker.
the speaker.
z When the "S.Back" setting (vpage 28) is set to "1sp" , "SB" is
displayed.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
• When "Channel Level" is adjusted, the adjusted values are set for
all the surround modes. To adjust the channel level separately for the
different surround modes, use the operation see "Adjust the volume of
the different speakers" (vpage 53).
• Speakers set to "None" in the "Speaker Config. " (vpage 27) settings
are not displayed.
• When o is pressed while the subwoofer volume is set to "–12dB" , the
"Channel Level" setting switches to "OFF" .
• If output of the test tones begins while the muting mode is set, the
muting mode is canceled.
Default : Reset all channel level settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover Frequency Crossover : Outputs at below set frequency, each speaker's bass signal
output from the subwoofer.
Outputs at below set
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
frequency, each speaker's
250Hz
bass signal output from the
• Advanced : Set the low frequency signals to be output from the signals
subwoofer. Set this according
of the respective speakers to the subwoofer.
to the low frequency
•
Front / Center / Surround / S.Back / Front Height :
reproduction capabilities of
· 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
the speakers you are using.
250Hz : Set the crossover frequency.
This can be set when
"Speaker Config. " –
"Subwoofer" (vpage
27) is set to "Yes" or
"No" .
Remote control
2
operation buttons
Setting contents
Select the speaker.
Displaying the menu
:
: Moves the cursor (Up/Down/Left/Right)
Cancel the menu
Setting items
Crossover Frequency
• Always set the crossover frequency to "80 Hz" . When using small
speakers, however, we recommend setting the crossover frequency
to a higher frequency.
• For speakers set to "Small" , sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
according to the "Bass Setting" setting (vpage 28).
· When "LFE" is selected, speakers set to "Small" at "Speaker
Config. " (vpage 27) can be set.
· When "LFE+Main" is selected, speakers can be set regardless of
the speaker size setting.
Front Speaker Setup Setting : Choose the method for setting the front speakers.
• Normal : The front speakers are set using the
Select front speakers to use
for each surround mode. • Custom : The front speakers used for the different playing modes are
set in advance.
2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
pure direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
MULTI CH : The front speakers used in modes other than the direct, stereo
and pure direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
NOTE
• When set to "Custom" ,
• The front speaker setting stored for the "Quick Select" function is given
priority.
: Decision the setting
Making detailed settings (Manual Setup)
Setting contents
.
does not operate.
: Return to previous menu