Settings; Making The Optimum Settings For The Connected Speakers - Denon AVR-890 Owner's Manual

Error Messages
If Audyssey Auto Setup could not be completed due to speaker installation, the measuring environment, etc., an error message is displayed. If
this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE Be sure to turn the power off before checking the speaker connections.
Error messages (examples)
• Included setup microphone is not connected.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
• Not all speakers could be detected.
N o m i c r o p h o n e o r S p e a k e r
• The front L speaker was not properly detected.
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Too much noise in the room for accurate
A U T O S E T U P
measurements to be made.
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
A m b i e n t n o i s e i s t o o h i g h
o r L e v e l i s t o o l o w • Speaker or subwoofer sound is too low for
accurate measurements to be made.
R e t r y
R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker could not be detected.
A U T O S E T U P
A U D Y S S E Y A U T O S E T U P M u l t E Q · The front R speaker were not properly detected.
C a u t i o n !
· Only one channel of the surround speakers was
F r o n t R N o n e
detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
R e t r y
· The surround back, but the surround speaker was
E N T E R E n t e r R E T U R N C a n c e l
not detected.
C h e c k c a u s e o f p r o b l e m !
• Displayed speaker connected with the polarities
A U T O S E T U P
reversed.
A U D Y S S E Y A U T O S E T U P M u l t E Q
C a u t i o n !
F r o n t L P h a s e
R e t r y
S k i p
E N T E R E n t e r R E T U R N C a n c e l
C h e c k c a u s e o f p r o b l e m !
n
To perform Audyssey Auto Setup again
Press ui to select "Retry", then press
n To cancel Audyssey Auto Setup
Press , the "Cancel auto setup?" prompt is displayed.
Press o p and select "Yes", then press
Remote control
operation buttons
Cause
• Connect the included setup microphone to the
• Check the speaker connections.
• Either turn off any device generating noise or
• Try again when the surroundings are quieter.
• Check the speaker installation and the direction
• Adjust the subwoofer's volume.
• Check the connections of the displayed
• Check the polarities of the displayed speaker.
• For some speakers, this error message may
.
.
Displaying the menu
:
: Moves the cursor (Up/Down/Left/Right)
Cancel the menu
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey™ Auto Setup)
Measures
SETUP MIC jack on the main unit.
move it away.
in which the speakers are facing.
speaker.
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press ui to select "Skip" , then press
.
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
This is displayed after Audyssey Auto Setup is completed.
1
Press ui to select
A U T O
P A R A M E T E R
"Parameter Check",
S p e a k e r
then press p or .
D i s t a n c e
C h a n n e l
C r o s s o v e r
E Q C h e c k
R e s t o r e
S h o w s p e a k e r
2
Use ui to select the item you want to check, then
press p or .
Speaker Config. Check
: Check the speaker configuration
Distance Check
: Check the distance
Channel Level Check
: Check the channel level
Crossover Freq. Check
: Check the crossover frequency
EQ Check
: Check the equalizer
3
o p
Use to switch the display between the different
speakers.
4
Press .
The confirmation screen reappears. Repeat steps 2 and 3.
Even if the settings are changed after Audyssey Auto Setup, Audyssey
Auto Setup settings can be restored by selecting "Restore" then
pressing .
: Decision the setting : Return to previous menu
ENGLISH
S E T U P
C H E C K
C o n f i g C h e c k
C h e c k
L e v e l C h e c k
C h e c k
c o n f i g u r a t i o n r e s u l t
Front
2