Master; Tuning; Output - Yamaha A4000 Owner's Manual

4. MASTER

Use this function to adjust the system's output pitch, to adjust
the level to the stereo outputs, and to set an assignable-output
destination for the stereo output signal.
Press the [UTILITY] button and then the [F4] button to go to
the MASTER function.
2 display pages are provided: Tuning, and Output.

Tuning

[UTILITY] Button [F4] Button
"UTIL-Tuning"
Use this page to adjust the tuning (shift the pitch) of all sys-
tem output.
Knob 1 Knob 2
Turn Tuning
Page
action Coarse
Press
Tree View QUICK...
action
Knob 1
[ Turn] Page
Selects display pages.
[ Press] Tree View
Calls the Tree View display (page 83).
Knob 2
[ Turn] Tuning Coarse
Turn the knob to adjust the tuning, in semitone incre-
ments.
[Range] -127 — +127
[ Press] QUICK...
Calls the quick entry menu (page 83).
Knob 3
[ Turn] Tuning Fine
Turn the knob to adjust the tuning in increments of
1.171875 cent.
(Note: 100 cents = 1 semitone)
[Range] -63 — +63
• The pitch of A (standard frequency = 440 Hz) as a
result of Master Tuning is displayed in Hertz above
the parameter's value.
[ Press] QUICK...
Calls the quick entry menu (page 83).
Knob 1 to select
Knob 3 Knob 4 Knob 5
Tuning Fine — —
QUICK... — —

Output

[UTILITY] Button [F4] Button
"UTIL-Output"
This function allows the signal appearing at the STEREO
OUTPUT jacks to simultaneously be sent to the assignable
outputs, and level offset can be individually applied for each
output.
• The setting that you make at this page takes precedence over the
assignable-output settings within samples and programs. If you
select AsgnOut2&3 at this page, for example, then AsgnOut2&3 will
always produce the same signal as the stereo outputs.
Cursor q
Cursor
q
Knob 1 Knob 2
Turn
Cursor/Page —
action
Press
Tree View —
action
Knob 1
[ Turn] Cursor/Page
Positions the cursor and selects display pages.
[ Press] Tree View
Calls the Tree View display (page 83).
Knob 4
[ Turn] Stereo Out To Assignable Out
You can select an assignable-output destination for the
stereo output signal — so that the stereo-output jacks
and the selected assignable-output connectors produce
exactly the same signal.
[Range] off, AsgnOutL&R, AsgnOut1&2 — AsgnOut5&6,
DIG&OPT
• off ... The stereo output signal is not simulta-
neously routed to any assignable output.
• AsgnOutL&R ... The stereo output signal is simul-
taneously routed to the Assignable Out L & R
outputs.
• AsgnOut1&2 — AsgnOut5&6 ... The stereo out-
put signal is simultaneously routed to the
specified Assignable Outputs.
• DIG&OPT ... The stereo output signal is simulta-
neously routed to the DIG&OPT (digital coax-
ial and optical) outputs.
• The AsgnOut1&2, AsgnOut3&4, AsgnOut5&6, and
DIG&OPT outputs cannot be selected unless the
optional AIEB1 I/O expansion board is installed.
A5000/A4000 •
UTILITY-MASTER
Knob 1 to select
Knob 3 Knob 4 Knob 5
Stereo Out To
— Assignable DIG&OPT Bit
Out
— — —
195
Chapter 8 UTILITY Mode