Roland RD-700GX Owner's Manual page 85

Parameter Value
D100:0W–
Balance
D0:100W
Level 0–127
DELAY
Parameter Value
Delay Mode ms, note
Delay (ms) 1–1300 ms
Delay ( ) note (*1)
Acceleration 0–15
Feedback -98– +98%
200–8000 Hz,
HF Damp
BYPASS
D100:0W–
Balance
D0:100W
Level 0–127
LINEDRIVE
This reproduces the distortion that occurs when an electrical
circuit is slightly overloaded.
Parameter Value
Strength SOFT, HARD
Type 1/2
Drive 0–127
Low Gain -15– +15 dB
High Gain -15– +15 dB
Level 0–127
Description
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
Description
When this is set to "note," the effect is
synchronized with the tempo.
Delay time from when sound is input to
delay until the delay sound is heard
(ms)
Delay time from when sound is input to
delay until the delay sound is heard
(note)
When you change the delay time, this
setting specifies the time over which it
will change from the current delay
time to the new setting. The speed of
pitch change will change together
with the delay time.
Specifies the percentage (%) of the
delay sound that will be returned to
the input.
Positive (+) settings return the sound at
the original phase, and negative (-)
settings return the phase-reversed
sound.
Specifies the frequency at which to cut
the high range of the delay sound
returned to the input.
Choose the BYPASS setting if you
don't want to cut.
Volume balance between the direct
sound (D) and the delay sound (W)
Output Level
Description
HARD produces stronger distortion
than SOFT.
Varies the nuances of the distortion.
Degree of distortion
This also affects the volume.
Boot or cut in the low end
Boot or cut in the high end
Output Level
Making Detailed Settings for the ONE TOUCH Tones
COMPRESSOR
Parameter
Attack 0–127
Threshold 0–127
Post Gain 0– +18 dB
Low Gain -15– +15 dB
High Gain -15– +15 dB
Level 0–127
WAH
Parameter
Control Type TOUCH, PEDAL
Filter Type LPF, BPF
Manual 0–127
Peak 0–100
Sens 1–127
Depth 0–127
Level 0–127
RING MOD
Parameter
Frequency 0–127
Sens 0–127
Polarity UP, DOWN
D100:0W–
Balance
D0:100W
Level 0–127
Value Description
This sets the time it takes until the level
is compressed after the input exceeds
the THRESHOLD.
Adjusts the volume at which
compression begins
Adjusts the output gain.
Boot or cut in the low end
Boot or cut in the high end
Output Level
Value Description
Effect Control Types
TOUCH: The tone changes in response
to changes in the volume.
PEDAL: The tone changes according to
the function of the Manual parameter.
Filter Type
LPF: The wah effect will be applied
over a wide frequency range.
BPF: The wah effect will be applied
over a narrow frequency range.
When Control Type is set to "PEDAL,"
you can use this parameter to modify
the tonal character.
Adjusts the amount of the wah effect
that will occur in the range of the
center frequency.
Set a higher value to narrow the range
to be affected.
When Control Type is set to
"TOUCH," this adjusts the sensitivity to
the volume used in changing the tone.
Depth of modulation
Output Level
Value Description
Adjusts the frequency at which
modulation is applied.
Adjusts the amount of frequency
modulation applied.
Determines whether the frequency
modulation moves towards higher
frequencies (UP) or lower frequencies
(DOWN).
Volume balance between the direct
sound (D) and the effect sound (W)
Output Level
85