Roland RD-700GX Owner's Manual page 181

Parameter Value
Acceleration 0–15
200–8000 Hz,
HF Damp
BYPASS
Pan L64–0–63R
Low Gain -15– +15 dB
High Gain -15– +15 dB
D100:0W–
Balance
D0:100W
Level 0–127
106: *2V PCH SFT
(2 VOICE PITCH SHIFTER)
A Pitch Shifter shifts the pitch of the direct sound. This 2-voice
pitch shifter has two pitch shifters, and can add two pitch
shifted sounds to the direct sound.
MFX Control Balance, Coarse A, Coarse B
Parameter Value
Mode 1, 2, 3, 4, 5
-24– +12
Coarse A
semitone
-24– +12
Coarse B
semitone
-100– +100
Fine A
cent
-100– +100
Fine B
cent
Pre Delay A 0.0–500.0 ms
Pre Delay B 0.0–500.0 ms
Pan A L64–0–63R
Pan B L64–0–63R
Description
This parameter adjusts the time over
which the Delay Time will change from
the current setting to a newly specified
setting. The rate of change for the
Delay Time directly affects the rate of
pitch change.
Adjust the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Adjust the stereo location of the delay
sound. L64 is far left, 0 is center, and
63R is far right.
Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Adjust the volume balance between
the direct sound and the delay sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the delay
sound will be output.
Adjust the output level.
Assignable Parameters
Description
Higher settings of this parameter will
result in slower response, but steadier
pitch.
Adjust the pitch of Pitch Shift A in
semitone steps (-2–+1 octaves).
Adjust the pitch of Pitch Shift B in
semitone steps (-2–+1 octaves).
Make fine adjustments to the pitch of
Pitch Shift A in 2-cent steps (-100–
+100 cents).
One cent is 1/100th of a semitone.
Make fine adjustments to the pitch of
Pitch Shift B in 2-cent steps (-100–
+100 cents).
One cent is 1/100th of a semitone.
Adjust the time delay from when the
direct sound begins until the Pitch Shift
A sound is heard.
Adjust the time delay from when the
direct sound begins until the Pitch Shift
A sound is heard.
Adjust the stereo location of the Pitch
Shift A sound. L64 is far left, 0 is
center, and 63R is far right.
Adjust the stereo location of the Pitch
Shift B sound. L64 is far left, 0 is
center, and 63R is far right.
Parameter Value
A100:0B–
Level Bal
A0:100B
D100:0W–
Balance
D0:100W
Level 0–127
107: *FBK P.SFT
(FEEDBACK PITCH SHIFTER)
This pitch shifter allows the pitch shifted sound to be fed back
into the effect.
MFX Control Balance, Coarse, Feedback
Parameter Value
Mode 1, 2, 3, 4, 5
-24– +12
Coarse
semitone
-100– +100
Fine
cent
Pre Delay 0.0–500.0 ms
Feedback -98– +98%
Pan L64–0–63R
Low Gain -15– +15 dB
High Gain -15– +15 dB
D100:0W–
Balance
D0:100W
Level 0–127
108: *REVERB
The Reverb effect adds reverberation to the sound, simulating
an acoustic space.
Assignable Parameters
MFX Control Time, Type, Balance
Effect/Parameter List
Description
Adjust the volume balance between
the Pitch Shift A and Pitch Shift B
sounds.
When set to A100:0B, only the sound
of Pitch Shift A is output; when set to
A0:100B, only the sound of Pitch Shift
B is output.
Adjust the volume balance between
the direct sound and the pitch shift
sound. With a setting of D100:0W
only the direct sound will be output,
and with a setting of D0:100W only
the pitch shift sound will be output.
Adjust the output level.
Assignable Parameters
Description
Higher settings of this parameter will
result in slower response, but steadier
pitch.
Adjust the pitch of the pitch shifted
sound in semitone steps (-2–+1
octaves).
Make fine adjustments to the pitch of
the pitch shifted sound in 2-cent steps
(one cent is 1/100th of a semi tone).
Adjust the time delay from when the
direct sound begins until the pitch
shifted sound is heard.
Adjust the proportion (%) of the
processed sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Adjust the stereo location of the pitch
shifted sound. L64 is far left, 0 is
center, and 63R is far right.
Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Adjust the volume balance between
the direct sound and the pitch shift
sound. With a setting of D100:0W
only the direct sound will be output,
and with a setting of D0:100W only
the pitch shift sound will be output.
Adjust the output level.
181