Omron EJ1G User Manual page 200

Parameter List
Variable Category Add-
type ress
D1 (91) Can be 0100 Bank 1 Set Point - CH1
changed
0101 Bank 1 Proportional Band - CH1
during
operation.
0102 Bank 1 Integral Time - CH1
0103 Bank 1 Derivative Time - CH1
0104 Bank 1 SP Ramp Rise Value - CH1
0105 Bank 1 SP Ramp Fall Value - CH1
Not used.
010D Bank 1 Alarm Value 1 - CH1
010E Bank 1 Alarm Upper Limit Value 1 - CH1
010F Bank 1 Alarm Lower Limit Value 1 - CH1
0110 Bank 1 Alarm Value 2 - CH1
0111 Bank 1 Alarm Upper Limit Value 2 - CH1
0112 Bank 1 Alarm Lower Limit Value 2 - CH1
0113 Bank 1 Alarm Value 3 - CH1
0114 Bank 1 Alarm Upper Limit Value 3 - CH1
0115 Bank 1 Alarm Lower Limit Value 3 - CH1
Not used.
0200 Bank 1 Set Point - CH2
4000 Bank 1 Set Point - CH64
Variable Category Add-
type ress
D2 (92) Can be 0100 Bank 2 Set Point - CH1
changed
0101 Bank 2 Proportional Band - CH1
during
operation.
0102 Bank 2 Integral Time - CH1
0103 Bank 2 Derivative Time - CH1
0104 Bank 2 SP Ramp Rise Value - CH1
0105 Bank 2 SP Ramp Fall Value - CH1
Not used.
010D Bank 2 Alarm Value 1 - CH1
010E Bank 2 Alarm Upper Limit Value 1 - CH1
010F Bank 2 Alarm Lower Limit Value 1 - CH1
0110 Bank 2 Alarm Value 2 - CH1
0111 Bank 2 Alarm Upper Limit Value 2 - CH1
0112 Bank 2 Alarm Lower Limit Value 2 - CH1
0113 Bank 2 Alarm Value 3 - CH1
0114 Bank 2 Alarm Upper Limit Value 3 - CH1
0115 Bank 2 Alarm Lower Limit Value 3 - CH1
Not used.
0200 Bank 2 Set Point - CH2
4000 Bank 2 Set Point - CH64
Note The decimal point position is determined by the sensor selection. With analog inputs, the decimal point
position is determined by the Decimal Point Position B parameter setting. In this case, however, the 0
(****) decimal point position setting will be treated as a setting of 1 (***.*).
Parameter name
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' 00000001 to H' 0000270F (1 to 9999)
H' 00000000 to H' 00000F9F (0 to 3999)
H' 00000000 to H' 0000270F (0.0 to 999.9)
H' 00000000 to H' 0000270F (0 to 9999)
(Function stops when set to 0.)
H' 00000000 to H' 0000270F (0 to 9999)
(Function stops when set to 0.)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
The rest are the same as channel 1.
Parameter name
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' 00000001 to H' 0000270F (1 to 9999)
H' 00000000 to H' 00000F9F (0 to 3999)
H' 00000000 to H' 0000270F (0.0 to 999.9)
H' 00000000 to H' 0000270F (0 to 9999)
(Function stops when set to 0.)
H' 00000000 to H' 0000270F (0 to 9999)
(Function stops when set to 0.)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
H' FFFFF831 to H' 0000270F ( 1999 to 9999)
The rest are the same as channel 1.
Setting (monitor) range
Setting (monitor) range
Appendix
Defau- Unit Attribut- Target Unit
lt es
TC4/ HFU
TC2
0 EU BANK ---
80 EU (See BANK ---
note.)
233 Seconds BANK ---
40.0 Seconds BANK ---
0 EU/s or BANK ---
EU/min
0 EU/s or BANK ---
EU/min
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
Defau- Unit Attribut- Target Unit
lt es
TC4/ HFU
TC2
0 EU BANK ---
80 EU (See BANK ---
note.)
233 Seconds BANK ---
40.0 Seconds BANK ---
0 EU/s or BANK ---
EU/min
0 EU/s or BANK ---
EU/min
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
0 EU BANK ---
179