Table of Contents
Advertisement
2. Local remote controller
2-6. Wireless remote controller [PAR-FL32MA / PAR-FA32MA]
PAR-FL32MA
It can operate in a group system without requiring
address settings.
When operating, it displays LED lamps. When
errors occur, the error code can be shown by the
LED flash count.
If an indoor unit with different functionality is operating inside the
same group, please note there may be cases when functionality
is partially disabled for batch control.
Wireless remote controllers can only be used for a single refrig-
erant system.
If you use a system controller to centrally control a group, you
will need cross-wiring between indoor units when using a wire-
less remote controller.
Also ensure there is no difference between the group setting of
the main system controller and the cross wiring across indoor
units when wiring and setting cross wires.
External dimension
PAR-FL32MA
58[2-
/
]
9
32
CHECK TEST RUN
MODEL SELECT
°C
AMPM
AMPM
NOT AVAILABLE
ON/OFF
TEMP
ON/OFF
HEAT
COOL
PAR-FA32MA
(Signal receiving unit)
19[
/
]
3
4
CONTROLLER
Functions
Item
ON and OFF operation for a single group
ON/OFF
Switches between Cool / Dry / Fan / Heat / Auto.
Operation mode
Operation modes vary depending on the air conditioner unit.
switching
Auto only supported for the City Multi R2 and WR2 series.
Sets the temperature for a single group
Range of temperature setting
Temperature
Cool/Dry :
19°C - 30°C (14°C - 30°C) / 67°F - 87°F (57°F - 87°F)
setting
17°C - 28°C (17°C - 28°C) / 63°F - 83°F (63°F - 83°F)
Heat :
Auto :
19°C - 28°C (17°C - 28°C) / 67°F - 83°F (63°F - 83°F)
( ) For PEFY/PFFY by setting DipSW 7-1 to ON and limits to NI6H fan speed only.
Set to PAR-FL32MA according to its Installation Manual 4 "Model setting".
Models with 4 air flow speed settings: Hi/Mid-1/Mid-2/Low
Fan speed setting
Models with 3 air flow speed settings: Hi/Mid/Low
Models with 2 air flow speed settings: Hi/Low
Auto setting varies depending on the model.
Air flow direction angles (4-angle, Swing) Auto Louver ON/OFF.
Air flow direction
Air flow direction settings vary depending on the model.
setting
Timer operation
One ON/OFF setting can be set for one day.
Individually prohibit operation of each local remote control
Permit / Prohibit
function (ON/OFF, Change operation mode, Set temperature,
local operation
Reset filter).
If operation is performed when the local remote controller
inactivation command is received from the main system
controller, a buzzer will ring and an LED will flash.
Indoor unit intake
Measures the intake temperature of the indoor unit when the
temperature
indoor unit is operating.
When an error occurs on the air conditioner unit, the operation
Error
lamp on the signal receiving unit will flash.
This operates air conditioner units in test run mode.
Test run
Ventilation
Up to 16 indoor units can be connected to an interlocked system
equipment
that has one LOSSNAY.
Some models will have different display for the air flowdirection and fan speed.
Set the air flow direction and fan speed when performing initial setting.
System example
Non-polarized
Signal
2-wire
receiving
unit
Wireless
remote
controller
PAR-FA32MA
22.5[
70[2-
/
]
3
4
ON/OFF
HEAT
COOL
:Each unit
:Each group
:Each floor
:Collective
Description
Operations Display
Non-
Non-
polarized
polarized
2-wire
2-wire
Signal
Signal
receiving
receiving
unit
unit
Wireless
Wireless
remote
remote
controller
controller
7
/
]
9.9[
/
]
8
3
8
4.8[
3
/
]
16
9.2[
3
/
]
8
Unit:mm[in.]
C7-R Rev.
:Each block
:Not available
1
3 - 9
Advertisement
Chapters
Table of Contents
