Mitsubishi Electric CITY MULTI PEFY-P22VMS-E-S Data Book page 33

1. SPECIFICATIONS
Model
Power source
Cooling capacity
(Nominal)
*2 Power input
*2 Current input
Heating capacity
(Nominal)
*2 Power input
*2 Current input
External finish
External dimension HxWxD
Net weight
Heat exchanger
FAN Type x Quantity
*4 External static press.
Motor Type
Motor output
Driving mechanism
Air flow rate
Sound pressure level (measured in anechoic room)
Insulation material
Air filter
Protection device
Refrigerant control device
Connectable outdoor unit
Liquid (R410A)
Diameter of refrigerant
pipe
Gas (R410A)
Field drain pipe size
Drawing External
Wiring
Refrigerant cycle
Standard attachment Document
Accessory
Optional parts Drain pump
Remarks
Notes :
1.Nominal cooling conditions
Indoor:27°CDB/19°CWB(81°FDB/66°FWB), Outdoor:35°CDB(95°FDB)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
2.The values are measured at the factory setting of external static pressure.
3.Nominal heating conditions
Indoor:20°CDB(68°FDB), Outdoor:7°CDB/6°CWB(45°FDB/43°FWB)
Pipe length:7.5m(24-9/16ft.), Level difference:0m(0ft.)
4.The factory setting of external static pressure is shown without < >.
Refer to "Fan characteristics curves", according to the external static pressure, in DATA BOOK for the usable range of air flow rate.
PEFY-P100VMM-E-S
1-phase 220-240V
50Hz
*1 kW 11.2
*1 kcal / h 9,600
*1 BTU / h 38,200
kW 0.3
A 1.38
*3 kW 12.5
*3 kcal / h 10,800
*3 BTU / h 42,700
kW 0.3
A 1.38
Galvanized steel plate
mm 325 x 1,415 x 740
inch 12-13/16 x 55-3/4 x 29-3/16
kg(lbs) 62(137)
Cross fin(Aluminum fin and
copper tube)
Sirocco fan x 2
Pa 50 - <110>
mmH O 5.1 - <11.2>
2
1-phase induction motor
kW 0.200
Direct-driven by motor
(Low-High)
3
m / min 23.0 - 33.0
L/s 383 - 550
cfm 812 - 1,165
(Low-High)
*2 dB <A> 40-44
Polyethylene foam
PP honeycomb fabric.
Fuse
LEV
R410A CITY MULTI
mm(in.) 9.52(3/8) Flare
mm(in.) 15.88(5/8) Flare
Socket (R1) + R1(PT1)
mm(in.)
[O.D.34(1-11/32)]
W660159
W660141
-
Installation Manual, Instruc-
tion Book
Insulation pipe for refrigerant
pipe, Tie band
PAC-KE04DMC-F
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be re-
ferred to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
When the bottom inlet is used, the noise pressure level is 5 to 10 dB greater than when the rear inlet is used.
Take appropriate noise reduction measures on site when using the bottom inlet.
INDOOR UNITS
PEFY-P125VMM-E-S
1-phase 220-240V
50Hz
14.0
12,000
47,800
0.4
1.9
16.0
13,800
54,600
0.4
1.9
Galvanized steel plate
325 x 1,415 x 740
12-13/16 x 55-3/4 x 29-3/16
65(144)
Cross fin(Aluminum fin and
copper tube)
Sirocco fan x 2
50 - <110>
5.1 - <11.2>
1-phase induction motor
0.280
Direct-driven by motor
(Low-High)
28.0 - 40.0
467 - 667
989 - 1,413
(Low-High)
42-47
Polyethylene foam
PP honeycomb fabric.
Fuse
LEV
R410A CITY MULTI
9.52(3/8) Flare
15.88(5/8) Flare
Socket (R1) + R1(PT1)
[O.D.34(1-11/32)]
W660159
W660141
-
Installation Manual, Instruc-
tion Book
Insulation pipe for refrigerant
pipe, Tie band
PAC-KE04DMC-F
C7-R Rev.
Unit converter
kcal =kW x 860
BTU/h =kW x 3,412
3
cfm =m /min x 35.31
lbs =kg / 0.4536
*Above specification data is
subject to rounding variation.
1 - 30