Electrical Wiring Diagrams - Mitsubishi Electric CITY MULTI PEFY-P22VMS-E-S Data Book

6. ELECTRICAL WIRING DIAGRAMS

LGH-15, 25, 35, 50, 65RX
LGH-80, 100RX -C2
4
CN10
ORANGE
BLUE
M
WHITE
2
SUPPLY C
FAN MOTOR
CN9
ORANGE
BLUE
M
WHITE
1
1
C
EXHAUST
FAN MOTOR
Operation monitor output
MIN
MAX
AC240V 2A AC220V 100mA 10
DC 5V 100mA
DC 24V 2A
9
8
Malfunction monitor or Pre-Heater output
7
(SW 5-6 can be changed)
MAX MIN
AC240V 2A AC220V 100mA
DC 5V 100mA
DC 24V 2A
TM2
External control input
-C2
4
BROWN
RED
CN8-1
CN8-2
DSA1
ZNR102
FUSE
S1
5
BLUE
250V 5A
X3
HIGH ZNR101
SW4 C101
X4
S2 BROWN
EXTRA
1
HIGH
3 WHITE
CN1
5
X1
1 WHITE
HIGH
YELLOW
X5
1
SW3
X2
CN7
EXTRA 3
RED
HIGH
BROWN
CN2
TM3 BROWN
CN16
CN32
X7
SW2
SW1
X8
BLACK
BLACK
SW5 CN5
BLACK
BLACK
ORANGE
SA1 SA2
CN6
ORANGE
TM4
TB5
1 2 3 1 2 A B S
Shield wire
M-NET-transmission cable
12V or
24V DC
Mr.Slim
Transmission
(non-polar)
cable
Lossnay Unit
1 3 PZ- PZ-
MAX 15 units
41SLB-E 52SF-E
Uncharged
a-contact
INDOOR UNITS
NOTE
1. TM1, TM2, TM3, TM4, TB5 shown in dotted lines are
field work.
2. Breaker should be provided by the customer.
3. Be sure to connect the grounding wire.
*Attention
1. This must be used with Mitsubishi Electric Air-
Conditioner Network System. (MELANS)
2. External control input (TM2) is impossible to use on
the Lossnay addressed to "Sub" (SW1) unit.
3. PZ-41SLB-E and PZ-52SF-E cannot be used simulta-
neously.
M1:
M2:
C:
GM:
LS:
TH1:
TH2:
SW1:
SW2, 5: Switch (Function selection)
SW3:
SW4:
TM1:
TM2:
TM3:
POWER SUPPLY
220V~ TM4:
50Hz
*1TB5:
BREAKER
TM1
S1, S2: Connector (Power supply)
L L
TR:
X7:
N N
X8:
CN1:
CN2:
CN5:
TR
CN6:
GM
CN7:
LS
CN8-1: Tab connector (Fan motor)
CN8-2: Tab connector (Fan motor)
CN9:
CN10: Connector (Fan motor)
TH1(OA)
CN16: Connector (High/Low switch)
CN32: Connector (Remote control selection)
*1SA1:
TH2(RA)
*1SA2:
MARK
CN16
Uncharged
a-contact
High
Low
High/Low select connector
Symbol explanation
Motor for exhaust fan
Motor for supply fan
Capacitor
Motor for Bypass movement
Microswitch
Thermistor for outside air
Thermistor for return air
Switch (Main/Sub change)
High/E. high select switch (Exhaust fan)
High/E. high select switch (Supply fan)
Terminal block (Power supply)
Terminal block
(Transmission cable and external control input)
Terminal block (Monitor output)
Terminal block (Transmission cable)
Terminal block (M-NET Transmission cable)
Control circuit transformer
Relay contact (For operation monitor output)
Relay contact
(For malfunction monitor output)
Connector (Transformer primary)
Connector (Transformer secondary)
Connector (Thermistor)
Connector (Microswitch)
Connector (Motor for Bypass operation)
Connector (Fan motor)
Address setting rotary switch (10 digit)
Address setting rotary switch (1 digit)
: Indicates terminal block
: Connector
: Board insertion connector or fastening
connector of control board
C7-R Rev.
6. E L E C T R I C A L W I R I N G D I A G R A M S
1 - 112