Table of Contents
Advertisement
9.3
User Information User Information
Alternatively, the unit's programmer lets you
choose from 6 different programmes for each
day of the week.
To set up programmes "P1" to "P6", select the
desired programme using the "-" and "+" keys,
and press "set" to select. The "P1 Enable" menu
appears.
To run a user set program P1 the timer/ chrono
must be enabled and also the program must be
enabled
To run a user set program P1 the timer/ chrono
must be enabled and also the program must be
enabled
Press "Set" again and when the display starts to
flash, press the "+" or "-" keys to select "On" or
"Off". Press "ok" to confirm the selection. Press
the "+" key to go to the "start" time.
To set the starting time for Programme P1, press
"set". The display starts to flash. Press the "+"
or "-" key to select the time and then press "ok"
to confirm. Press the "+" key to go to the P1 ."
Stop" menu.
Once the pre-set time is elapsed, the unit shuts
down. At the start of the Shutdown phase,
another timer for a different pre-set period of
time is triggered (Start-up delay time: factory
setting: 20 minutes), that will make the unit
To set the set point temperature for Programme
enter the activation phase, when the thermostat
P1, press "Set". The display starts to flash. Press
closes contact (NC)
the "+" or "-" key to select the desired
Start-up delay time (Delay time On): The
temperature, followed by "Ok" to confirm.
delay time that elapses between the moment
the thermostat closes (NC) until the unit is
activated.
Shutdown delay time (Delay time Off): The
delay time that elapses between the
moment the thermostat opens (OC) until the
unit starts to shutdown.
Note: When using the feature for the first time,
you must press the On/Off button in the
To set the operating power level (1 to 5) of
display. To enable the eco mode, press "set".
Programme P1, press "Set". The display starts to
The display starts to flash. To activate the eco
flash. Press the "+" or "-" key to select the
mode, press "set". The display starts to flash.
desired power level (1 to 5), and then "Ok" to
Select "On" or "Off" using the "-" and "+"
confirm. Press the "+" key to go to the "Days"
keys. Press "set" to confirm the selection.
menu.
Back Light
To Select " back light" , press "set". The
display starts to flash. Press the "+" or "-" key
to select the time for the screen to light up, or
select "On" to keep the light permanently on.
Press "ok" to confirm.
Remote Control.
To select the days of the week that you want P1
This feature enables and disables the remote
Programme to run, press "set" and then select the
control, when the user wants to operate the
day of the week using the "-" and "+" keys. Press
unit's thermostat remotely. Press "Set" and use
"set". The display starts to flash. Select "On" or
the "+" and "-" keys to select the "On" or "Off"
"Off" using the "-" and "+" keys. Press "ok" to
mode. Press "Ok" to confirm. Press the "+"
confirm the selection. Press the "esc" key to go to
key to go to the "temperature units" menu.
the "Days" menu. Press the "esc" key again to
Note: Some TV remote controls share the same
go to the "program " menu.
frequency as the unit's remote control,
Press the "+" key to move on to the next menu.
possibly influencing the unit's operation. If this
is the case, it is recommended to disable the
18
Repeat the steps to set up Programs P2 to P6 or
remote control feature.
as many as are required.
ºC/ºF
Once the programs are set remember to "enable"
To select ºC / ºF, press "set". The display starts
them.
to flash. Press the "+" or "-" key to select "ºC",
Advertisement
Table of Contents
