Configuring For Kns Operation; Lan Connection Settings; Administrator Settings - Kenwood TS-890S Instruction Manual

Configuration Using ARHP-890
To manage remote users and perform login authentication using
ARHP-890 as with the TS-990S, TS-590S, and TS-590SG,
configure the system as shown in Figure 3.
Internet
Broadband Broadband
Router Router
Remote PC with
ARCP-890
.
Figure 3: System Configuration for Remote User
Management and Login Authentication via ARHP
Under this configuration, the registered users list is managed by
the ARHP-890. ARHP-890 performs login authentication of the
remote user, while at the same time logs in to the TS-890S as an
administrator. After logging in, command communication and
voice communication between the TS-890S and ARCP-890 are
relayed.
• The built-in VoIP of TS-890S is used for voice communication
(ARVP-10 or a non-KENWOOD VoIP can also be used for voice
communication).
It is necessary to configure the settings to transmit
●
incoming control commands and VoIP data via Internet
from the broadband router to each device. Please refer
to the "TS-890S KENWOOD NETWORK COMMAND
SYSTEM Setting Manual".
Configuration for KNS Operation in a Home LAN
Environment
To operate the TS-890S remotely in a home LAN environment,
configure the system as shown in Figure 4.
Broadband Router
ARCP-890
Figure 4: KNS System Configuration in a Home LAN .
Environment
Under this configuration, ARCP-890 logs in to the TS-890S as an
administrator (login as a registered user is also possible).
• The built-in VoIP of TS-890S is used for voice communication.
It is also possible to make use of the USB audio function by
connecting a USB cable (ARUA-10 is needed).
• Another alternative option is to extract analog audio output
signal (ANO) and analog audio input signal (ANI) from the ACC
2 connector and connect to the audio input/output connector of
the PC sound card.
Hub
LAN Connection
Host PC with
TS-890S
ARHP-890
Hub
LAN Connection
TS-890S
NETWORK/KNS OPERATION 15

Configuring for KNS Operation

LAN Connection Settings

Follow the steps below to configure the LAN connection
environment for KNS operation.
1 Press [MENU].
2 Press F [KNS].
The KNS status screen for confirming the settings is displayed.
• If F [KNS] is not displayed, press F [MORE] to display F
[KNS].
3 Press F4 [CONFIG].
The KNS configuration screen appears.
.
4 Press F2 [
]/ F3 [
"KNS Operation (LAN Connector)".
5 Press F4 [SELECT].
6 Press F2 [–]/ F3 [+] to select the setting.
Setting Value Off (default)/ On (LAN)/ On (Internet)
On (LAN): When operating KNS in a home LAN environment.
On (Internet): When operating KNS via the Internet.
• Pressing F [KNS TOP] returns the display to the KNS status
screen.
The KNS Operation cannot be changed to a value other
●
than "Off" without first configuring the administrator
settings

Administrator Settings

Administrator refers to the owner of the radio equipment (manager
of the radio equipment in the case of a club station).
• To connect the transceiver to LAN and perform remote
operation from a PC via LAN, login authentication is needed.
An administrator ID and password are configured for the
transceiver in advance by the administrator, which are then
used to log in to the transceiver from ARCP-890.
• Upon logging in with the administrator ID, the KNS menu can
be operated from ARCP-890.
1 Select KNS Menu [1] "Administrator ID" and KNS
Menu [2] "Administrator Password".
2 Press F4[EDIT].
] to select KNS Menu [0]
15-3