Kenwood TS-890S Instruction Manual page 162

16 OTHER FUNCTIONS
Parameter Behavior of Assigned Functions
Press Switches between the FSK and PSK modes
FSK/PSK
Press
Switches to the reverse mode
and hold
Press Band Direct selection (GENE)
GENE
Press
Switches the transverter to ON or OFF
and hold
Press Switches between RX filters A, B and C
IF FIL
Press Starts up or exits the RX filter configuration
and hold screen
Switches the frequency lock function to ON
LOCK Press
or OFF
LSB/USB Press Switches between the LSB and USB modes
Starts up the memory scroll mode and
M.IN Press
registers a memory channel
Press Switches between memory and VFO
M/V, M>V
Press
Memory shift
and hold
Switches the TX output power limiter to ON
Press
or OFF
MAX-Po
Press Starts up or exits the TX output power limit
and hold configuration screen
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 1 message 1
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 2 message 2
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 3 message 3
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 4 message 4
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 5 message 5
Message Starts transmission of CW/RTTY/PSK
Press
Memory CH 6 message 6
Message Starts transmission of RTTY/PSK
Press
Memory CH 7 message 7
Message Starts transmission of RTTY/PSK
Press
Memory CH 8 message 8
METER Press Switches the meter type
MHz Press Switches to the MHz mode
Switches the TX monitor function to ON or
MONI Press
OFF
Mute (Sub Switches the sub-receiver audio mute to
Press
Receiver) ON or OFF (use for Split Transfer B)
Press Switches NB1 to ON or OFF
NB1
Press Starts up or exits the NB1 level
and hold configuration screen
Press Switches NB2 to ON or OFF
NB2
Press Starts up or exits the NB2 level
and hold configuration screen
NCH Press Switches the notch filter to ON or OFF
Switches the noise reduction mode
Press
(NR1/NR2/OFF)
NR
Starts up or exits the NR1 level
Press
configuration screen or NR2 level
and hold
configuration screen
PLAY Press Starts or pauses playback of a file recording
PRE Press Preamplifier selection
Press Switches the speech processor to ON or OFF
PROC
Press Starts up or exits the speech processor
and hold configuration screen
16-4
Parameter Behavior of Assigned Functions
Q-M.IN Press Registers to a quick memory
Press Calls up a quick memory
Q-MR
Press
Deletes all quick memory data
and hold
Press Starts or pauses manual recording
REC
Press
Writes full-time recording data to a file
and hold
RIT Press Switches RIT to ON or OFF
Press Switches the RX antenna to ON or OFF
RX ANT
Press Switches the antenna output for the
and hold external receiver to ON or OFF
Press Switches the RX DSP equalizer to ON or OFF
RX EQ
Press
Starts up or exits the RX equalizer screen
and hold
Press Switches the RX monitor to ON or OFF
Switches the RX monitor (squelch forcibly
RX Monitor
Press
opened) to ON or OFF <only while the key
and hold
is pressed and held down>
Safe Removal of
Press Unmounts the USB flash drive
USB Flash Drive
Press Starts or stops scanning
Starts up or exits VFO/Program Scan
SCAN
Press
segment configuration screen/Memory
and hold
Scan group configuration screen
SCP Press Switches to the SCOPE screen
SEND Press Enables or disables the TX mode
Press Switches split operation to ON or OFF
SPLIT
Press Starts configuration of the frequency for
and hold split operation
STOP Press Stops recording or playback
SWL Press Switches SWL display mode to ON or OFF
TF-SET Press Switches TF-SET to ON or OFF
Press Turning ON/OFF TX Equalizer
TX EQ
Press
Starts up or exits the TX equalizer screen
and hold
TX TUNE1 Press Starts or ends TX Tune 1
Starts or ends TX Tune 2
Press
TX TUNE2 <This behavior is only applicable when the
and hold
key is pressed and held down>
Increases the frequency (in VFO mode)
Moves to a larger channel number (in
UP Key
Press memory channel mode)
(Microphone)
Moves up the menu or to a larger setting
value (on menu configuration screen)
VOICE1 Press Starts the voice guide (VOICE1 function)
VOICE2 Press Starts the voice guide (VOICE2 function)
VOICE3 Press Starts the voice guide (VOICE3 function)
Press Switches VOX to ON or OFF
VOX
Press Starts up or exits the VOX configuration
and hold screen
XIT Press Switches XIT to ON or OFF
Off Press Does not assign any function