Kenwood TS-890S Instruction Manual page 190

18 TROUBLESHOOTING
ID
The storage location cannot be changed while a PSK QSO log
0049
recording. (ERR: 0049)
Audio files cannot be copied while an audio recording. (ERR:
004D
004D)
Communication log files (CW) cannot be copied while a CW QSO
004E
log recording. (ERR: 004E)
Communication log files (RTTY) cannot be copied while a RTTY
004F
QSO log recording. (ERR: 004F)
Communication log files (PSK) cannot be copied while a PSK
0050
QSO log recording. (ERR: 0050)
KNS log files cannot be copied while a KNS log recording. (ERR:
0051
0051)
Audio files cannot be deleted while an audio recording. (ERR:
0055
0055)
Communication log files (CW) cannot be deleted while a CW QSO
0056
log recording. (ERR: 0056)
Communication log files (RTTY) cannot be deleted while a RTTY
0057
QSO log recording. (ERR: 0057)
Communication log files (PSK) cannot be deleted while a PSK
0058
QSO log recording. (ERR: 0058)
KNS log file cannot be deleted while a KNS log recording. (ERR:
0059
0059)
Copying was aborted due to the number of files exceeded 255 in
005B the destination folder. (ERR: 005B)
Reduce the number of files in UBS flash drive and then copy again.
The selected file cannot be read because the market code is
005C
different. (ERR: 005C)
The current sourced from the USB connector exceeds the upper
0103 limit value. (ERR: 0103)
Remove the USB device and then restart the transceiver.
PLL unlock was detected. (ERR: 0105)
0105
Refer to "Troubleshooting" in the instruction manual.
No reference signal has been detected. (ERR: 0107)
0107 Ensure that the reference signal has been sourced to the REF IN
(10 MHz) connector.
Corruption of the data was detected. (ERR: 0109)
Executing the Full Reset will initialize the transceiver to the
0109
defaults.
Press [OK] (F) to start the Full Reset.
010A to
010F, A DSP error was detected. (ERR: 010A to 010F, 0110 to 0115)
0110 to Refer to "Troubleshooting" in the instruction manual.
0115
A hardware error was detected. (ERR: 0117)
0117
Refer to "Troubleshooting" in the instruction manual.
Turn off the power of the regulated DC power supply after "A system error has occurred." message is displayed.
●
If error occurs frequently, try updating to the latest firmware. If the same problem persists, this transceiver could be faulty.
●
Please contact KENWOOD service center.
18-10
Message Description/Corrective Action
Appears when attempting to change the destination for saving the file
while PSK communication log recording is in progress.
Appears when attempting to copy files to a PC or USB while manual
recording is in progress.
Appears when attempting to copy files to a PC or USB while CW
communication log recording is in progress.
Appears when attempting to copy files to a PC or USB while RTTY
communication log recording is in progress.
Appears when attempting to copy files to a PC or USB while PSK
communication log recording is in progress.
Appears when attempting to copy files to a PC or USB while KNS log
recording is in progress.
Appears when attempting to delete files while manual recording is in
progress.
Appears when attempting to delete files while CW communication log
recording is in progress.
Appears when attempting to delete files while RTTY communication log
recording is in progress.
Appears when attempting to delete files while PSK communication log
recording is in progress.
Appears when attempting to delete files while KNS log recording is in
progress.
Appears when the number of files at the copy destination has exceeded
the maximum limit of 255 files while copy is in progress.
The transceiver type does not match the transceiver type that created
the settings data file.
Appears when overcurrent is detected at the USB connector.
Disconnect unused USB devices.
Perform Full Reset. If PLL unlock is still detected after Full Reset, note
down the error message number (ERR:0105) and send an inquiry to
KENWOOD service center.
Appears when there is no reference signal input from an external source.
Check whether there is signal input to the REF IN terminal and whether
the level of the signal is high enough.
Appears when damage is found in the backup data.
Press F [OK] to perform Full Reset.
Perform Full Reset.
If the same error message appears again after Full Reset, note down
the error message number (ERR: 010A to 010F, 0110 to 0115) and send
an inquiry to KENWOOD service center.
Perform Full Reset.
If the same error message appears again after Full Reset, note down
the error message number (ERR:0117) and send an inquiry to
KENWOOD service center.