Endress+Hauser RID14 Operating Instructions Manual
Fieldbus indicator with foundation fieldbus protocol
Hide thumbs
Also See for RID14:
- Operating instructions manual (68 pages) ,
- Brief operating instructions (44 pages) ,
- Brief operating instructions (24 pages)
Related Manuals for Endress+Hauser RID14
Summary of Contents for Endress+Hauser RID14
- Page 1 Products Solutions Services BA00282R/09/EN/16.23-00 71616048 2023-01-31 Valid from version 02.00.xx (device software) Operating Instructions RID14 Fieldbus indicator with FOUNDATION Fieldbus™ protocol...
-
Page 2: Table Of Contents
Table of contents RID14 Table of contents About this document ....3 Maintenance ..... . 29 Symbols . -
Page 3: About This Document
RID14 About this document About this document Symbols 1.1.1 Safety symbols DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious or fatal injury. WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or fatal injury. -
Page 4: Documentation
For an overview of the scope of the associated Technical Documentation, refer to the following: • Device Viewer (www.endress.com/deviceviewer): Enter the serial number from the nameplate • Endress+Hauser Operations app: Enter serial number from nameplate or scan matrix code on nameplate. 1.2.1 Document function... -
Page 5: Safety Instructions
RID14 Safety instructions Document type Purpose and content of the document Safety Instructions (XA) Depending on the approval, safety instructions for electrical equipment in hazardous areas are also supplied with the device. The Safety Instructions are an integral part of the Operating Instructions. -
Page 6: Product Safety
Incoming acceptance and product identification RID14 Modifications to the device Unauthorized modifications to the device are not permitted and can lead to unforeseeable dangers! ‣ If modifications are nevertheless required, consult with the manufacturer. Repair To ensure continued operational safety and reliability: ‣... -
Page 7: Product Identification
(www.endress.com/deviceviewer): all the information about the device and an overview of the Technical Documentation supplied with the device are displayed. • Enter the serial number on the nameplate into the Endress+Hauser Operations App or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations App: all the information about the device and the technical documentation pertaining to the device is displayed. -
Page 8: Mounting
Mounting RID14 3.4.1 FOUNDATION Fieldbus™ certification The field indicator successfully passed all tests and is certified and registered by the Fieldbus Foundation. The measuring system meets all the requirements of the following specifications: • Certified in accordance with FOUNDATION Fieldbus™ specification •... -
Page 9: Mounting The Measuring Device
RID14 Mounting Mounting the measuring device The device can be mounted directly on the wall → 9. A mounting bracket is available for pipe mounting → 3, 10. The backlit display can be mounted in four different positions → 9. -
Page 10: Post-Mounting Check
Electrical connection RID14 A0011258 3 Mounting the field indicator on a pipe with a mounting bracket for pipe diameters 1.5" to 2.2" Mounting plate Mounting bracket 2 M6 nuts Post-mounting check After installing the device, always perform the following checks:... -
Page 11: Connecting The Measuring Device
RID14 Electrical connection • Via a conventional cable gland • Via a fieldbus connector (optional, available as an accessory) Connecting the measuring device 5.2.1 Connecting the cable to the field indicator Proceed as follows to wire the field indicator: A0012568 ... - Page 12 Fieldbus connector As an option, a fieldbus connector can be screwed into the field housing instead of a cable gland. Fieldbus connectors can be ordered from Endress+Hauser as an accessory (see ' A ccessories' section). The connection technology of FOUNDATION Fieldbus™ allows devices to be connected to the fieldbus via uniform mechanical connections such as T-boxes, junction boxes etc.
- Page 13 RID14 Electrical connection This connection technology using prefabricated distribution modules and plug-in connectors offers substantial advantages over conventional wiring: • Field devices can be removed, replaced or added at any time during normal operation. Communication is not interrupted. • Installation and maintenance are significantly easier.
- Page 14 Electrical connection RID14 The electrical data of the fieldbus cable have not been specified but determine important characteristics of the design of the fieldbus, such as distances bridged, number of users, electromagnetic compatibility, etc. Type A Type B Cable structure...
- Page 15 RID14 Electrical connection Shielding and grounding NOTICE Equalizing currents can damage the bus cable or bus shield ‣ If the shielding of the cable is grounded at more than one point in systems without potential matching, mains frequency equalizing currents can occur that damage the bus cable or the bus shield or have a serious effect on signal transmission.
-
Page 16: Ensuring The Degree Of Protection
Electrical connection RID14 a switch. If this is not the case, a separate bus terminator must be installed. Please also note the following: • In the case of a branched bus segment, the measuring device furthest from the segment coupler represents the end of the bus. -
Page 17: Operation Options
RID14 Operation options Operation options Overview of operation options 6.1.1 Display A0012574 9 LC display of the field indicator Bar graph display in increments of 10% with indicators for underranging (item 1a) and overranging (item 1b) Measured value display, status indication "Bad measured value status"... -
Page 18: Access To The Operating Menu Via The Operating Tool
Operation options RID14 You can make the following hardware settings for the fieldbus interface using miniature switches (DIP switches) on the electronics module → 19: Switching the hardware write protection on/off Not used WRITE LOCK A0011638 10 Hardware configuration of the field indicator Listener mode The field indicator analyzes the devices active on the bus. -
Page 19: Hardware Settings
RID14 System integration 6.2.1 System files The following files are required for commissioning and configuring the network: • Commissioning → Device description (DD :*. Sym ,*. Ffo) • Network configuration → CFF file (Common File Format) These files can be acquired as follows: •... - Page 20 System integration RID14 For fieldbus configuration information, please refer to Operating Instructions BA00013S “FOUNDATION Fieldbus Overview: Installation and Commissioning Guidelines”. 7.1.1 System architecture The following diagram shows an example of a FOUNDATION Fieldbus™ network with associated components. Field controller High speed Ethernet (HSE)
- Page 21 RID14 System integration High Speed Ethernet (HSE): The superior bus system is implemented via the High Speed Ethernet (HSE) with a transmission rate of max. 100 MBit/s. This serves as the ' b ackbone' (basic network) between various local sub-networks and/or where there is a large number of network users.
- Page 22 System integration RID14 The field device tag name (PD_TAG) is assigned for the device in question during commissioning (see Operating Instructions). It remains stored in the device even if the supply voltage is interrupted. 7.1.5 Function blocks The FOUNDATION Fieldbus™ uses predefined function blocks to describe the functions of a device and to specify uniform data access.
-
Page 23: Commissioning
ID, device type and device serial number. It is unique and can never be assigned twice. The structure of the DEVICE_ID can be broken down as follows: DEVICE_ID = 452B4810CF-XXXXXXXXXXX 452B48 = Endress+Hauser 10CF = RID1x XXXXXXXXXXX = Device serial number (11-digit) - Page 24 4. Switch on the device. The first time you establish a connection, the device responds as follows in the configuration program: EH_RID14-xxxxxxxxxxx (Tag name PD TAG for RID14, xxx... = serial number) 452B4810CF-xxxxxxxxxxx (DEVICE_ID) for RID1x Block structure → 24 5.
- Page 25 RID14 Commissioning Block description Permanent Block category Standard Input Selector 1 Standard Input Selector 2 Standard Arithmetic Standard Integrator Standard The device is delivered from the factory with the bus address "247" and is therefore in the address range reserved for changing the address of field devices. A lower bus address should be assigned to the device for commissioning.
-
Page 26: Diagnostics And Troubleshooting
Diagnostics and troubleshooting RID14 Diagnostics and troubleshooting Troubleshooting instructions In the event of a critical error, it might be necessary to return the indicator to the manufacturer for repair. Follow the instructions in → 30 before returning the indicator. -
Page 27: Status Messages
RID14 Diagnostics and troubleshooting Problems when configuring function blocks Transducer Blocks: Check whether the operating mode of the Resource Block is set to AUTO → The operating mode MODE_BLK parameter group/TARGET parameter. cannot be set to AUTO. Transducer Blocks: The device description file (Device Description, DD) has not yet been loaded to the The manufacturer-specific host system or the configuration program? →... -
Page 28: Firmware History
Diagnostics and troubleshooting RID14 Category No. Status message Display Cause of error/remedy symbol • CURRENT_STATUS_ NUMBER in the 'Advanced Diagnostics' Transducer Block • Display 261 Device status message (FF): No bar graph Cause of error: Electronics board displayed Error in the electronics. -
Page 29: Maintenance
A clean, dry cloth can be used to clean the device. Repair 11.1 General information In accordance with the Endress+Hauser repair principle, the devices have a modular design and repairs can be carried out by the customer. For more information on service and spare parts, please contact your supplier. 11.1.1 Repairs to Ex-approved devices •... -
Page 30: Return
3x thread NPT 1/2, w/o terminal block 3x M20x1.5, w/o terminal block 3x thread G1/2, w/o terminal block Version: Standard RIA141G- ← complete order code for RID14 housing Item No. Type Order number Housing cover cpl. display, aluminum Ex d + RIA141X-HK seal Housing cover cpl. -
Page 31: Disposal
Various accessories are available for the device, and can be ordered with the device or at a later stage from Endress+Hauser. Detailed information on the specific order code is available from your local Endress+Hauser sales organization or on the product page of the Endress+Hauser website: www.endress.com. -
Page 32: Technical Data
Technical data RID14 Technical data 13.1 Communication 13.1.1 Failure information Status message as per the fieldbus specification. 13.1.2 Switch-on delay 13.1.3 FOUNDATION Fieldbus™ • FOUNDATION Fieldbus™ H1, IEC 61158-2 • FDE (Fault Disconnection Electronic) = 0 mA • Data transmission rate, supported baudrate: 31.25 kBit/s •... - Page 33 RID14 Technical data Link settings Slot time Min. Inter PDU delay Max. response delay Blocks Block description Block index Permanent Block execution time Block category Resource Extended Display Transducer Manufacturer-specific Advanced Diagnostic Manufacturer-specific 1100 30 ms Standard Input Selector 1...
-
Page 34: Power Supply
Technical data RID14 13.2 Power supply 13.2.1 Terminal assignment A0021528 14 Terminal assignment of the field indicator Fieldbus connection 13.2.2 Supply voltage The power is supplied via the fieldbus. U = 9 to 32 V , polarity-independent (max. voltage U = 35 V). -
Page 35: Environment
RID14 Technical data 13.4 Environment 13.4.1 Ambient temperature range –40 to +80 °C (–40 to +176 °F) The display may react slowly at temperatures < –20 °C (–4 °F). At temperatures < –30 °C (–22 °F) the readability of the display can no longer be guaranteed. -
Page 36: Mechanical Construction
Technical data RID14 13.5 Mechanical construction 13.5.1 Design, dimensions 132 (5.2) 112 (4.4) 106 (4.2) 121 (4.8) 166 (6.5) A0011152 15 Dimensions of the field indicator in mm (in) • Die-cast aluminum housing for general applications, or optional stainless steel housing •... -
Page 37: Operability
RID14 Technical data 13.6 Operability 13.6.1 Local operation Display elements A0011307 16 LC display of the field indicator (backlit, can be plugged in 90° stages) Bar graph display in increments of 10% with indicators for underranging (item 1a) and overranging (item 1b) Measured value display, digit height 20.5 mm (0.8 in), status indication "Bad measured value status"... -
Page 38: Certificates And Approvals
13.8 Supplementary documentation The following types of documentation are available on the product pages and in the Download Area of the Endress+Hauser website (www.endress.com/downloads) (depending on the selected device version): Document Purpose and content of the document Technical Information (TI) -
Page 39: Resource Block
RID14 Appendix block may be regarded as a container in which parameters and the associated functionalities are contained. A FOUNDATION™ Fieldbus device has the following block types: • A Resource Block (device block): The Resource Block contains all the device-specific features of the unit. - Page 40 Appendix RID14 14.2.1 Selecting the operating mode The operating mode is set via the MODE_BLK parameter group. The Resource Block supports the following operating modes: • AUTO (automatic mode) • OOS (out of service) The ' O ut Of Service' (OOS) mode is also shown via the BLOCK_ERR parameter. In the OOS operating mode, you can access all the write parameters without restriction if write protection is not enabled.
- Page 41 This parameter is required only for interoperability tests and has no significance in normal operation. DD Resource Read only Displays the source for the device description in the device. (DD_RESOURCE) Display: (BLANK SPACE) Manufacturer ID Read only Displays the manufacturer' s ID number. (MANUFAC_ID) Display: 0 x 452B48 = Endress+Hauser Endress+Hauser...
- Page 42 Appendix RID14 Resource Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Device type (DEV_TYPE) Read only Displays the device ID number in hexadecimal format. Display: 0 x 10CF hex for RID1x Device Revision (DEV_REV) Read only Use this function to view the device revision number.
- Page 43 RID14 Appendix Resource Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Free Time (FREE_TIME) Read only Displays the free system time available (as a percentage) for the execution of additional function blocks. This parameter always displays the value 0 because the function blocks of the device are preconfigured.
- Page 44 Appendix RID14 Resource Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Acknowledge Option AUTO - OOS This parameter is used to specify whether a process alarm must be acknowledged by (ACK_OPTION) the fieldbus host system when the alarm is detected. If the option is activated, the process alarm is acknowledged automatically.
- Page 45 RID14 Appendix Resource Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Factory setting: Operator Field device diagnostic Read only The main version of the FF field diagnostic specification which was used for version (FD_VER) development purposes for this device.
-
Page 46: Transducer Blocks
Appendix RID14 Resource Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Block Error Description 1 Read only Displays additional information to troubleshoot a block error. (BLOCK_ERR_DESC_1) • Simulation permitted: simulation is permitted with the activated simulation switch •... - Page 47 RID14 Appendix Transducer Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Block Mode (MODE_BLK) AUTO - OOS Displays the actual and target operating mode of the corresponding Transducer Block, the permitted modes which the Resource Block supports and the normal operating mode.
- Page 48 Appendix RID14 Transducer Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) Possible display: • No Error (normal state) • Electronics Failure • Data Integrity Error • Mechanical Failure • Configuration Error • Calibration Error • General Error...
- Page 49 RID14 Appendix Transducer Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) DISP_VALUE_1_SETTINGS AUTO - OOS This parameter defines all the values for the setup of the indicator. The following DISP_VALUE_2_SETTINGS parameters are included: DISP_VALUE_3_SETTINGS • DISP_VALUE_1[...8]_LISTENER_MODE: DISP_VALUE_4_SETTINGS Activates the "Listener mode".
- Page 50 Appendix RID14 Transducer Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) • DISP_VALUE_1[...8]_DESC: Use this function to enter customized text, max. 16 characters. This text is shown beneath the value. The text will scroll if it is longer than 5 characters.
- Page 51 RID14 Appendix 14.3.5 Transducer Block "Advanced Diagnostic" The Advanced Diagnostic Block provides information about the current and last device status. In addition, it also indicates the channel in which the current diagnostic event occurred. It contains minimum and maximum values for every analog channel.
-
Page 52: Pid Function Block (Pid Controller)
Appendix RID14 Transducer Block Parameter Parameters Write access Description Index with operating mode (MODE_BLK) STATUS_SIGNAL Read only Copy of "ACTUAL_STATUS_CATEGORY" but with the "Status signal" label Block Error Description 1 Read only Displays additional information to troubleshoot a block error. -
Page 53: Configuration Of The Device Behavior When Events Occur In Accordance With Foundation Fieldbus™ Field Diagnostics
RID14 Appendix negative, or net flow. This capability is useful to calculate volume or mass variation in vessels or as an optimization tool for flow ratio control. The Integrator function block supports mode control, demand reset, a reset counter, and signal status calculation. - Page 54 Appendix RID14 14.8.2 Assignment parameters Event categories are assigned to event groups via four assignment parameters. They can be found in the RESOURCE Block (RB2): • FD_FAIL_MAP: for the "Failure (F)" event category • FD_CHECK_MAP: for the "Function check (C)" event category •...
- Page 55 RID14 Appendix A0019661 In the FD_FAIL_MAP parameter of the Resource Block, deselect the corresponding check box for the "Highest Configuration" group. A0019663 In the FD_CHECK_MAP parameter of the Resource Block, tick the corresponding check box for the "Highest Configuration" group.
-
Page 56: Transmission Of Event Messages To The Bus
Appendix RID14 YYY = Diagnostic number The value in the example above is 1437 14.9 Transmission of event messages to the bus The process control system used must support the transmission of event messages. 14.9.1 Event priority Event messages are only transmitted to the bus if their priority is between 2 and 15. -
Page 57: Index
RID14 Index Index Alarm detection and processing ....40 Manufacturer-specific parameters ....46 Arithmetic function block . - Page 60 *71616048* 71616048 www.addresses.endress.com...