Table of Contents
Advertisement
7)
Press the <ENTER> button.
f The [3COLORS:RED], [3COLORS:GREEN], [3COLORS:BLUE], or [3COLORS:WHITE] screen is
displayed.
When [7COLORS] is selected, the [7COLORS:RED], [7COLORS:GREEN], [7COLORS:BLUE],
[7COLORS:CYAN], [7COLORS:MAGENTA], [7COLORS:YELLOW], or [7COLORS:WHITE] screen is
displayed.
f By setting [AUTO TESTPATTERN] to [ON], the test pattern for the selected color is displayed.
8)
Press as to select [RED], [GREEN], or [BLUE].
f Only [GAIN] can be adjusted when [WHITE] is selected for [3COLORS].
9)
Press qw to adjust.
f The adjustment value will change between 0
*1 The lower limit varies depending on the color to be adjusted.
Note
f Operation when correcting the adjustment color
When the correction color same as the adjustment color is changed: The luminance of the adjustment color changes.
When correction color red is changed: Red is added to or subtracted from the adjustment color.
When correction color green is changed: Green is added to or subtracted from the adjustment color.
When correction color blue is changed: Blue is added to or subtracted from the adjustment color.
f Since advanced skills are necessary for the adjustment, this adjustment should be carried out by a person who is familiar with the projector
or by a service person.
f Set [AUTO TESTPATTERN] to [ON] to automatically display a test pattern for use in adjusting the selected adjustment colors.
f The selected adjustment item will return to the factory default value when the <DEFAULT> button on the remote control is pressed.
f When [COLOR ADJUSTMENT] is set to anything other than [OFF], the [DISPLAY OPTION] menu → [COLOR CORRECTION] cannot be
set.
About [POSITION DATA]
If [MULTI IMAGE PROJECTION] → [ADJUST MODE] is set to [AUTO], then [ASPECT], [SHIFT] and [ZOOM] of
[POSITION DATA] will be automatically adjusted according to input signal resolution, [SCREEN FORMAT], [EDGE
BLENDING], [NUMBER OF PROJECTORS] and [ORDER].
If [MULTI IMAGE PROJECTION] → [ADJUST MODE] is set to [MANUAL], then [ASPECT], [SHIFT] and [ZOOM]
of [POSITION DATA] can be set manually only.
Note
f You can also manually adjust [ASPECT], [SHIFT] and [ZOOM] of [POSITION DATA] even if [ADJUST MODE] is set to [AUTO]. However,
in this case if you perform the following operations after manually adjusting [POSITION DATA], the settings of [POSITION DATA] will be
changed automatically.
g Change the setting of [SCREEN FORMAT], [NUMBER OF PROJECTOR] or [ORDER].
g Switch [EDGE BLENDING] to [ON] or [OFF].
g Switch [EDGE BLENDING] → [LEFT]/[RIGHT] to [ON] or [OFF].
g Change the setting of [EDGE BLENDING] → [LEFT]/[RIGHT] → [START]/[WIDTH]
f If [MULTI IMAGE PROJECTION] → [ADJUST MODE] is set to [AUTO], the following menus are not synchronized with [ASPECT], [SHIFT]
and [ZOOM] of [POSITION DATA] and cannot be set. If [MULTI IMAGE PROJECTION] → [ADJUST MODE] is switched from [AUTO] to
[MANUAL], the following menus will return to the settings before [ADJUST MODE] was set to [AUTO].
g The [POSITION] menu → [SHIFT]
g The [POSITION] menu → [ASPECT]
g The [POSITION] menu → [ZOOM]
[ASPECT]
You can switch the aspect ratio of the image.
The aspect ratio is switched within the screen range selected in [SCREEN FORMAT]. Set [SCREEN FORMAT] first.
Æ
(
page 82)
1)
Press as to select [MULTI IMAGE PROJECTION].
2)
Press the <ENTER> button.
f The [MULTI IMAGE PROJECTION] screen is displayed.
3)
Press as to select [ASPECT].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
Chapter 4 Settings - [POSITION] menu
and 2 048.
*1
ENGLISH - 87
Advertisement
Chapters
Table of Contents
