Panasonic PT-CMZ50 Operating Instructions Manual page 175

<HDMI IN 1> terminal
<HDMI IN 2> terminal
<HDMI OUT> terminal
<DIGITAL LINK/LAN>
terminal
<LAN> terminal
Connecting
<COMPUTER IN> terminal
terminals
<AUDIO IN> terminal
<AUDIO OUT> terminal
<USB (VIEWER/
WIRELESS/DC OUT)>
terminal
<SERIAL IN> terminal
Acoustic noise
*1
Operating temperature
Operating
environment
Operating humidity
Operation position
Power requirements
Rated current
Maximum power consumption
Standby mode power consumption
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2020 international standards.
*2 The projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level.
If the operating environment temperature exceeds the following value, the light output may be reduced to protect the projector.
f When using the projector at an altitude lower than 1 400 m (4 593') above sea level: 34 °C (93 °F)
f When using the projector at an altitude between 1 400 m (4 593') and 2 700 m (8 858') above sea level: 30 °C (86 °F)
*3 The projector's operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) when the optional wireless module
(Model No.: AJ-WM50 Series) is attached.
Chapter 7 Appendix - Specifications
HDMI x 2, HDCP compatible, Deep Color compatible, CEC supported
Audio signal Linear PCM (sampling frequency: 48 kHz/44.1 kHz/32 kHz)
HDMI x 1, CEC not supported
RJ-45 x 1, for network and DIGITAL LINK connections (HDBaseT
2) compatible, 100Base-TX, HDCP compatible, Deep Color compatible
RJ-45 x 1, for network connection, PJLink (class 2) compatible, 10Base-T/100Base-TX
High-density D-Sub 15 p (female) x 1
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
RGB signal
VD
YP P signal Y: 1.0 V [p-p] including synchronization signal, P
B R
M3 stereo mini jack x 1, 0.5 V [rms], input impedance 22 kΩ or more
M3 stereo mini jack x 1, monitor output and stereo compatible, 0 V [rms] to 2.0 V [rms]
(variable), output impedance 2.2 kΩ or lower
USB connector (type A) x 1, for Memory Viewer function/ Wireless module (Model No.:
AJ-WM50 Series) connection/power supply (DC 5 V, maximum 2 A)
D-Sub 9 p x 1, RS-232C compliant, for computer control
When [LIGHT POWER] in [ECO MANAGEMENT] is set to [NORMAL] or
34 dB
[ECO].
25 dB When [LIGHT POWER] in [ECO MANAGEMENT] is set to [QUIET]
0 °C (32 °F) to 45 °C (113 °F)
*2*3
20 % to 80 % (no condensation)
[FRONT/CEILING], [FRONT/DESK], [REAR/CEILING], [REAR/DESK]
110 V ~ (110 V alternating current), 60 Hz (for Taiwan)
100 V - 240 V ~ (100 V - 240 V alternating current), 50 Hz/60 Hz (for other countries and
regions)
3 A (for Taiwan)
3.4 A - 1.4 A (for other countries and regions)
325 W (The power consumption is 310 W at 200 V - 240 V.)
Approx. 0.5 W When [STANDBY MODE] is set to [ECO]
When [STANDBY MODE] is set to [NORMAL]
f [QUICK STARTUP] function is disabled
f [IN STANDBY MODE] of [AUDIO SETTING] is set to [OFF]
Approx. 18 W
f No device is connected to <DIGITAL LINK/LAN> terminal
f <USB (VIEWER/WIRELESS/DC OUT)> terminal is not in use
When [STANDBY MODE] is set to [NORMAL]
f [QUICK STARTUP] function is disabled
f [IN STANDBY MODE] of [AUDIO SETTING] is set to [ON]
Approx. 51 W
f A device is connected to <DIGITAL LINK/LAN> terminal
f <USB (VIEWER/WIRELESS/DC OUT)> terminal is in use
When [STANDBY MODE] is set to [NORMAL]
f [QUICK STARTUP] function is enabled
f [IN STANDBY MODE] of [AUDIO SETTING] is set to [ON]
Approx. 85 W
f A device is connected to <DIGITAL LINK/LAN> terminal
f <USB (VIEWER/WIRELESS/DC OUT)> terminal is in use
TTL high impedance, automatic positive/negative polarity
compatible
TTL high impedance, automatic positive/negative polarity
compatible
compliant), PJLink (class
TM
P : 0.7 V [p-p] 75 Ω
B R
ENGLISH - 175