Table of Contents
Advertisement
Setting [STANDBY MODE]
Set the power consumption during standby and whether to enable the [QUICK STARTUP] function.
1)
Press as to select [ECO MANAGEMENT].
2)
Press the <ENTER> button.
f The [ECO MANAGEMENT] screen is displayed.
3)
Press as to select [STANDBY MODE].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
[NORMAL]
[ECO]
f Proceed to Step 5) when [NORMAL] is selected.
5)
Press as to select [QUICK STARTUP].
6)
Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
f Proceed to Step 7) when [ON] is selected.
7)
Press the <ENTER> button.
f The [QUICK STARTUP] screen is displayed.
8)
Press qw to switch [VALID PERIOD].
f The items will switch each time you press the button.
[30MIN.]
[60MIN.]
[90MIN.]
Note
f When [STANDBY MODE] is set to [NORMAL], the network function can be used during standby.
f When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL], the
WIRELESS/DC OUT)> terminal can supply power even in standby state. If set to [ECO], the
terminal can not supply power in standby state.
f When [STANDBY MODE] is set to [ECO], the network function and the audio output function cannot be used during standby. Also, some
RS-232C commands cannot be used.
f When [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to
[NORMAL].
f [QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].
f When [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK
STARTUP] function is valid.
f If [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the
projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].
f When [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks red while in the standby mode during the period
when the [QUICK STARTUP] function is valid. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [OFF], the power indicator <ON
(G)/STANDBY (R)> will change to a red light when the specified time set in [VALID PERIOD] elapses after the projector enters the standby
mode. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [ON], even [QUICK STARTUP] is set to [ON], the power indicator <ON
(G)/STANDBY (R)> will not change to a red light when the specified time set in [VALID PERIOD] elapses.
f When [QUICK STARTUP] is set to [ON], the standby period when the [QUICK STARTUP] function is valid will be added as the projector
runtime.
[RS-232C]
Set the communication condition of the <SERIAL IN> terminal. Refer to "<SERIAL IN> terminal" (x page 170).
Chapter 4 Settings - [PROJECTOR SETUP] menu
Select this item when using the network function during standby.
Select this item to reduce power consumption during standby.
Disables the [QUICK STARTUP] function.
Enables the [QUICK STARTUP] function until the specified time set in [VALID PERIOD] elapses after
the projector enters the standby mode. The time until the projection starts after the power is turned on
will be reduced during the period when the [QUICK STARTUP] function is valid.
Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby
mode.
Select a desired valid period.
<
USB (VIEWER/
<
USB (VIEWER/WIRELESS/DC OUT)>
ENGLISH - 103
Advertisement
Chapters
Table of Contents
