Advertisement
Warning
EN
DVP04AD-S/DVP04AD-S2 is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity, electric shock
and vibration. To prevent non-maintenance staff from operating DVP04AD-S/DVP04AD-S2, or to prevent an accident from damaging
DVP04AD-S/DVP04AD-S2, the control cabinet in which DVP04AD-S/DVP04AD-S2 is installed should be equipped with a safeguard. For
example, the control cabinet in which DVP04AD-S/DVP04AD-S2 is installed can be unlocked with a special tool or key.
EN
DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring again before
DVP04AD-S/DVP04AD-S2 is powered up. After DVP04AD-S/DVP04AD-S2 is disconnected, Do NOT touch any terminals in a minute. Make
sure that the ground terminal
FR
DVP04AD-S/DVP04AD-S2 est un module OUVERT. Il doit être installé que dans une enceinte protectrice (boitier, armoire, etc.) saine,
dépourvue de poussière, d'humidité, de vibrations et hors d'atteinte des chocs électriques. La protection doit éviter que les personnes non
habilitées à la maintenance puissent accéder à l'appareil (par exemple, une clé ou un outil doivent être nécessaire pour ouvrir a protection).
FR
Ne pas appliquer la tension secteur sur les bornes d'entrées/Sorties, ou l'appareil DVP04AD-S/DVP04AD-S2 pourra être endommagé. Merci
de vérifier encore une fois le câblage avant la mise sous tension du DVP04AD-S/DVP04AD-S2. Lors de la déconnection de l'appareil, ne pas
toucher les connecteurs dans la minute suivante. Vérifier que la terre est bien reliée au connecteur de terre
interférence électromagnétique.
Introduction
Model Explanation & Peripherals
Thank you for choosing the Delta DVP series PLC. The analog input module DVP04AD-S/DVP04AD-S2 receives external 4-point
analog signal input (voltage or current) and converts it into 14-bit digital signals. A DVP series slim type PLC can read data from
DVP04AD-S/DVP04AD-S2 or write data to DVP04AD-S/DVP04AD-S2 by means of the instruction FROM/TO. There are 49 CRs
(control registers) in the module, and each register has 16 bits.
Users can select input from voltage or current via wiring. Voltage input range is ±10VDC (resolution is 1.25mV). Current input range
is ±20mA (resolution is 5μA).
Product Profile & Outline
1
25.20
3.00
90.00
2
3
4.00
1. POWER, RUN and ERROR indicators
2. Model name
3. DIN rail clip
4. I/O terminals
5. I/O point indicators
6. Mounting hole of the expansion unit
7. Nameplate
External Wiring
DVP04AD-S
Connected to
a power supply module
Ground (Impedance: Less than 100 )
on DVP04AD-S/DVP04AD-S2 is correctly grounded in order to prevent electromagnetic interference.
4
5
60.0
0
V+
C
I+
H
COM
1
FG
V+
C
I+
H
COM
2
FG
●
V+
C
I+
H
COM
3
FG
V+
C
I+
H
COM
4
FG
●
Vol tage input
-10V~+10V
Shiel ded
cable*1
Current input
-20mA~+20mA
Shielded
cable*1
on
DC24V
*4
System ground
6
7
8
10
9
3
Unit: mm
8. Extension port
9. Extension unit clip
10. DIN rail groove (35mm)
11. RS-485 communication port
12. Mounting groove of the extension unit
13. DC power input
14. Extension port
CH1
104.7K
V+
250
*5
I+
COM
FG
AG
100K
104.7K
CH4
V+
250
*2
I+
COM
FG
AG
100K
*3
D C /D C
24V
converter
0V
3.4
60.0
0
3.00
11
12
14
13
CH1
CH4
+15V
AG
-15V
ENGLISH
afin d'éviter toute
90.00
Figure 1
Arrangement of the
terminals
V+
I+
CO M
F G
V+
I+
CO M
F G
．
V+
I+
CO M
F G
V+
I+
CO M
F G
．
Advertisement
