Direction 5336113-1En, Revision - GE Healthcare Optima XR200amx Installation Manual

GE H
EALTHCARE
D 5336113-1EN, R
IRECTION
Revision history
Revision Date
1 26SEP2011
2 26OCT2011
3 14NOV2011
4 17OCT2011
5 28SEP2012
6 02AUG2013
7 12NOV2013
8 29APR2014
Page 10
10
EVISION
Reason for change
Initial release of document.
SPR HCSDM00103773 - Table 3-3 and Table 3-5 removing drive handle
SPR HCSDM00103774 - DAP installation
SPR HCSDM00103780 - Xray tube rating plate in wrong position
Validation updates. Refer to SPRs: HCSDM00108057, HCSDM00108062,
HCSDM00108063, HCSDM00108064
Validation updates. Refer to SPRs: HCSDM00109082 - Importing IP looks procedural
issue
Updated Chapter 4, Section 4.2.6.1 - Adding certificates and Section 4.2.6.2 - Configuring
broadcast SSID networks per FMI 10861A (see PR#7646877).
In Chapter 3, Section 3.5.2.1, step 1, changed text from "External" to "Enclosure
Leakage". Changed text instances from "probe" to "clamp" in Chapter 3, Sections 3.5.2.1
(step 5), 3.5.2.2 (step 3), 3.5.2.3 (step 3), 3.5.3.4 (step 3) and 3.5.3.5 (step 3).
Added text to front material on how to obtain most recent revisions of technical manuals.
Satisfies FDA recommendation.
Added 'Detector firmware download' procedure to Chapter 3, Section 3.6.4. Refer to SPR
HCSDM00157822.
Chapter 3, Section 3.5.2, added Notice about potential test equipment damage. Refer to
HCSDM00188252.
Chapter 4, Sections 4.10.3.1 and 4.10.3.2, added Notice regarding reset of system after
DAP is reconnected. Refer to HCSDM00188256.
Chapter 3, Section 3.6.3, added Caution message regarding wall plug. Refer to
TrackWise 10831134.
Chapter 4, Sections 4.10.3.1 and 4.10.3.2, added new steps 6 and 14 (respectively)
regarding DAP calibration reference to the System Manual. Refer to HCSDM00159583.
Chapter 2, Section 2.1, added Wireless Hand Switch (optional, Optima XR220amx and
Optima XR200amx) under "shipped separately". Refer to ECO 2162103.
Chapter 3, Section 3.5.1.5, changed bin measurement point in Table 3-3 to "Screw used
for mounting strain relief of wired handswitch cable". Changed picture for Fig 3-15 to show
new measurement point. Refer to ECO 2148874.
Chapter 4, Section 4.10.3, changed Figures 4-9 and 4-10 to show DAP meter in lower set
of collimator rails. Refer to HCSDM00264083.
Chapter 4, Section 4.10.3.2, added steps to remove cable cover and then put back on at
end of procedure. Refer to ECO 2160317.
Chapter 4, Section 4.10.4, added wireless exposure switch installation procedure. Refer
to ECO 2162103.
Preface
O XR200 /XR220
PTIMA AMX
I M
NSTALLATION
AMX
ANUAL