Hitachi SH1 Series Basic Manual page 59

Chapter 4
[AF120] to [AF152]
Brake control function
Code/Name
AF120
Contactor control enable,
1st-motor
AF121
Run delay time,
1st-motor
AF122
Contactor off delay time,
1st-motor
AF123
Contactor response
check time, 1st-motor
AF130
Brake control enable, 1st-motor
AF131
Brake release wait time,
1st-motor(Forward)
AF132
Brake wait time for
Accel., 1st-motor(Forward)
AF133
Brake wait time for
stopping, 1st-motor (Forward)
AF134
Brake confirmation signal
wait time, 1st-motor (Forward)
AF135
Brake release frequency
setting,1st-motor (Forward)
AF136
Brake release current
setting, 1st-motor (Forward)
AF137
Brake frequency,
1st-motor (Forward)
AF138
Brake release wait time ,
1st-motor (Reverse)
AF139
Brake wait time for
Accel. , 1st-motor (Reverse)
AF140
Brake wait time for
Stopping, 1st-motor (Reverse)
AF141
Brake wait time for
confirmation,
1st-motor (Reverse)
AF142
Brake release frequency
setting,
1st-motor (Reverse)
AF143
Brake release current
setting, 1st-motor (Reverse)
AF144
Brake frequency,
1st-motor (Reverse)
AF150
Brake open delay time,
1st-motor
AF151
Brake close delay time,
1st-motor
AF152
Brake response check
time, 1st-motor
Initial
Range (unit)
value
00(Disable)/
01(Enable:
primary side) 00
02(Enable:
secondary side)
0.00 to 2.00(s) 0.20
0.00 to 2.00(s) 0.10
0.00 to 5.00(s) 0.10
00(Disable)/
01(Brake control 1:
Common)/
00
02(Brake control 1:
Separate)/
03(Brake control 2)
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 590.00(Hz) 0.00
Inv
Inverter rated rated
current current
×(0.0 to 2.0)(A) ×
1.0(A)
0.00 to 590.00(Hz) 0.00
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 5.00(s) 0.00
0.00 to 590.00(Hz) 0.00
Inv
Inverter rated rated
current current
×(0.0 to 2.0)(A) ×
1.0(A)
0.00 to 590.00(Hz) 0.00
0.00 to 2.00(s) 0.20
0.00 to 2.00(s) 0.20
0.00 to 5.00(s) 0.10
4-16
For parameter configuration
Code/Name
AF153
Servo lock/ DC injection time
at start, 1st-motor
AF154
Servo lock/ DC injection time
at stop, 1st-motor
・
The parameters [AF120] to [AF153] set the brake control and
the contactor control.
In addition to these parameters, the brake control function
uses the input terminal 037[BOK] Answer back from Brake
and the output terminal 037[BRK] Brake release, 038[BER]
Brake error. And the contactor control function uses the input
terminal 107[COK] Contactor check signal and the output
terminal 039[CON] Contactor control.
For more information, contact your supplier or local Hitachi inverter
sales office.
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
AF201 DC braking selection, 2nd-motor
AF202 Braking type selection, 2nd-motor
AF203 DC braking frequency, 2nd-motor
AF204 DC braking delay time, 2nd-motor
AF205 DC braking force setting, 2nd-motor
AF206 DC braking active time at stop, 2nd-motor
AF207 DC braking operation method selection,
2nd-motor
AF208 DC braking force at start, 2nd-motor
AF209 DC braking active time at start, 2nd-motor
AF220 Contactor control enable, 2nd-motor
AF221 Run delay time, 2nd-motor
AF222 Contactor off delay time, 2nd-motor
AF223 Contactor response check time, 2nd-motor
AF230 Brake control enable, 2nd-motor
AF231 Brake release wait time,
2nd-motor (Forward)
AF232 Brake wait time for accel., 2nd-motor
(Forward)
AF233 Brake wait time for stopping, 2nd-motor
(Forward)
AF234 Brake confirmation signal wait time,
2nd-motor(Forward)
AF235 Brake release frequency setting, 2nd-motor
(Forward)
AF236 Brake release current setting, 2nd-motor
(Forward)
AF237 Braking frequency, 2nd-motor (Forward)
AF238 Brake release wait time, 2nd-motor (Reverse) Same as AF138
AF239 Brake wait time for accel., 2nd-motor
(Reverse)
AF240 Brake wait time for stopping,
2nd-motor(Reverse)
AF241 Brake confirmation signal wait time,
2nd-motor(Reverse)
AF242 Brake release frequency setting,
2nd-motor(Reverse)
AF243 Brake release current setting, 2nd-motor
(Reverse)
AF244 Braking frequency, 2nd-motor (Reverse side)
AF250 Brake open delay time, 2nd-motor
AF251 Brake close delay time, 2nd-motor
AF252 Brake response check time, 2nd-motor
AF253 Servo lock/DC injection time at
start,2nd-motor
AF254 Servo lock/DC injection time at stop,
2nd-motor
[AF153] to [AF254]
Initial
Range (unit)
value
0.00 to 10.00(s)
0.00 to 10.00(s)
Range Initial
(unit) value
Same as AF101
Same as AF102
Same as AF103
Same as AF104
Same as AF105
Same as AF106
Same as AF107
Same as AF108
Same as AF109
Same as AF120
Same as AF121
Same as AF122
Same as AF123
Same as AF130
Same as AF131
Same as AF132
Same as AF133
Same as AF134
Same as AF135
Same as AF136
Same as AF137
Same as AF139
Same as AF140
Same as AF141
Same as AF142
Same as AF143
Same as AF144
Same as AF150
Same as AF151
Same as AF152
Same as AF153
Same as AF154
0.60
0.60