Table of Contents
Advertisement
Figure 16 - Correct position of fan skirt installation.
•
Use the wire tie to secure the fan and rheostat wire
harnesses together to the tubing under the bottom of
ST240
the unit.
FDV attach fan
12/13/99 djt
Approved Vent System Components
The Intrepid Heater must be vented to the outdoors through
an adjacent exterior wall or through the roof. The venting
system must be comprised of the appropriate listed venting
components specified on this page. These parts are
available from DuraVent Corporation.
See Figure 4 for dimensions relevant to the standard
minimum-vent kits.
DuraVent Components
www.duravent.com
Phone: 1-800-835-4429, Fax: 1-707-446-4740
Minimum Horizontal Vent Kit
Venting Component required for:
Basic Straight Through-the-Wall Installation
Horizontal Termination Cap
Vermont Castings Group Zero Clearance
Sleeve (included)
Firestop
Wall Thimble Cover
24" Straight (Maximum length)
Hardware Package (2 req'd)
NOTE: DuraVent Wall Thimble, 46DVA-WT is not
approved for use with this appliance except in
noncombustible masonry walls.
For corner installation add:
45° Elbow, Blk.
Venting Components
90° Elbow, Blk.
45° Elbow, Blk.
6" Straight, Blk.
9" Straight, Blk.
8
⁄
" Pipe Extension, Blk
1
2
16" Pipe Extension, Blk
12" Straight
14
Figure 17 - Attach rheostat to bracket.
Venting System Components
24" Straight
36" Straight
48" Straight
Square Horizontal Termination Cap
Sconce Horizontal Termination Cap
Round Horizontal Termination Cap
Wall Plate
Vinyl Siding Standoff
Snorkel Termination - 14"
Snorkel Termination - 36"
Wall Strap
Cathedral Ceiling Support Box
46DVA-KHC
Storm Collar
Firestop Spacer
Flashing 0/12 - 6/12
46DVA-HRC
Flashing 6/12 - 12/12
Wall Thimble
54623
Wall Thimble Cover (Brass)
46DVA-WFS
Wall Firestop
46DVA-DC
Attic Insulation Shield
46DVA24B
Co-Linear Vent Adapter
56167
Steel Chimney Conversion Kit
Kit A (6
Kit B (6
Kit C (6
Masonry Chimney Conversion Kit
46DVA-E45B
Vertical Termination Cap (High Wind)
Vertical Termination Cap (Low Profile)
46DVA-E90B*
*Included in Minimum Horizontal Vent Kit
46DVA-E45B
All DuraVent Straight vent pipe sections have a net length
46DVA-06B*
1
⁄
" (37 mm) less than the nominal dimension; i.e., a 6"
1
2
46DVA-09B
(152 mm) Straight pipe section has an effective length of
46DVA-08AB*
4
⁄
" (115 mm).
1
2
46DVA-16AB
Refer to the DuraVent website for additional components.
46DVA-12
(www.duravent.com)
Retaining Nut
Rheostat Knob
ST347a
JUV
FK28
rheostat install
9/21/00
⁄
" - 8
⁄
")
5
5
8
8
⁄
" - 10
⁄
")
5
1
8
2
⁄
" - 13")
5
8
Rheostat
46DVA-24B*
46DVA-36B
46DVA-48
46DVA-HC
46DVA-HSC
46DVA-HRC
46DVA-DC*
46DVA-VSS
46DVA-SNK14
46DVA-SNK30
46DVA-WS
46DVA-CS
46DVA-SC
46DVA-FS
46DVA-F6
46DVA-F12
46DVA-WT*
3PVP-TKV
46DVA-WFS
46DVA-IS
46DVA-GCL
46DVA-KCA
46DVA-KCB
46DVA-KCC
46DVA-KMC
46DVA-VCH
46DVA-VC
46DVA-KHC
20012761
Advertisement
Table of Contents
