Table of Contents
Advertisement
Note
f [DYNAMIC CONTRAST] cannot be set when [DYNAMIC CONTRAST NX] is set to anything other than [OFF].
f To use the contrast synchronization function and the shutter synchronization function, make the menu setting identical for each linked
projector either by setting [PICTURE] menu → [DYNAMIC CONTRAST NX] to anything other than [OFF] or by setting [PICTURE] menu →
[DYNAMIC CONTRAST] to anything other than [OFF].
Set [DYNAMIC CONTRAST NX] to [OFF] and [DYNAMIC CONTRAST] to anything other than [OFF] when there are projectors without
[DYNAMIC CONTRAST NX] menu grouped into the linked projectors.
Performing desired correction
1)
Press as to select [DYNAMIC CONTRAST].
2)
Press qw or the <ENTER> button.
f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.
3)
Press qw to select [USER].
4)
Press the <ENTER> button.
f The [DYNAMIC CONTRAST] screen is displayed.
5)
Press as to select the item to set.
f The items of the detailed settings will switch each time you press qw.
f Press the <ENTER> button when [MULTI PROJECTOR SYNC] is selected.
[AUTO CONTRAST]
(Automatic light source
adjustment)
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness
level of the signal to start the
light adjustment)
[LIGHTS OUT TIMER]
(Time setting until the light
turns off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness
level of the signal to turn off
the light)
[LIGHTS OUT FADE-IN]
(Setting of fade-in when
lighting up again)
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[MANUAL INTENSITY]
(Manual light source
adjustment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
Chapter 4 Settings — [PICTURE] menu
Setting item
[OFF]
[1] - [255]
[6%] - [50%]
[DISABLE]
[0.0s] - [10.0s]
[0%] - [5%]
[OFF]
[0.5s] - [10.0s]
[OFF]
[0.5s] - [10.0s]
[0] - [255]
[OFF]
[1]
[2]
[3]
Details
Does not adjust the light source.
The higher the value, the stronger the light adjustment of the light
source.
Can be set in increments of 1. (Factory setting: 122)
Adjusts the light source when the brightness level of the image
signal being input gets lower than the set value. The higher the
value, the larger the range to perform the light adjustment of the
light source.
Can be set in increments of 1 %. (Factory setting: 46 %)
Does not turn off the light source.
Turns off the light source when the brightness level of the image
signal being input goes under the value set in [LIGHTS OUT
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s].
[0.0s] - [4.0s] can be selected in increments of 0.5.
Sets the level of the brightness of the image signal to turn off the
light source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
Does not set the fade-in of the image when the light source is
turned on again from the condition that the light source was turned
off with [LIGHTS OUT TIMER].
Sets the time to fade in the image when the light source is turned
on again from the condition that the light source was turned off with
[LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
Does not set the fade-out of the image when the light source is
turned off with [LIGHTS OUT TIMER].
Sets the time to fade out the image when the light source is turned
off with [LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
Does not compensate the signal.
Slightly compensates the signal.
Moderately compensates the signal.
Strongly compensates the signal.This setting will maximize the
contrast.
ENGLISH - 91
Advertisement
Table of Contents
