Table of Contents
Advertisement
[COMMAND]
[INPUT]
[OPERATING MODE]
*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*2 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 138)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[MULTI PROJECTOR SYNC]
Set the contrast synchronization function and the shutter synchronization function.
The contrast synchronization function is a function to display a combined screen with a balanced contrast by
sharing the brightness level of the image signal input to each projector when a multi-display is constructed
by combining the projected image of multiple projectors. The shutter synchronization function is a function to
synchronize the shutter operation of the specified projector to other projectors, and the effect using the shutter
function including the fade out/fade in operation can be synchronized.
To use the contrast synchronization function and the shutter synchronization function, it is necessary to connect
the projectors targeted for synchronization in a loop with daisy chain connection using the <SERIAL/MULTI
SYNC IN> terminal and the <SERIAL/MULTI SYNC OUT> terminal. For details of how to connect the projectors,
refer to "Connecting example when using the contrast synchronization function/shutter synchronization function"
(x page 51).
Note
f The contrast synchronization function and the shutter synchronization function can be used simultaneously.
f The menu items in the [PROJECTOR SETUP] menu → [MULTI PROJECTOR SYNC] is the same as the following setting items.
g The [PICTURE] menu → [DYNAMIC CONTRAST NX] → [USER] → [MULTI PROJECTOR SYNC]
g The [PICTURE] menu → [DYNAMIC CONTRAST] → [USER] → [MULTI PROJECTOR SYNC]
g The [DISPLAY OPTION] menu → [SHUTTER SETTING] → [MULTI PROJECTOR SYNC]
Setting the contrast synchronization function
1)
Press as to select [MULTI PROJECTOR SYNC].
2)
Press the <ENTER> button.
f The [MULTI PROJECTOR SYNC] screen is displayed.
3)
Press as to select [MODE].
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
[HDMI1]
[HDMI2]
[SDI]
[DIGITAL LINK]
[INPUT1] - [INPUT10]
[NORMAL]
[QUIET]
*2
[USER1]
[USER2]
[USER3]
Switches the input to HDMI1.
Switches the input to HDMI2.
Switches the input to SDI.
Switches the input to DIGITAL LINK.
Switches the input to DIGITAL LINK, and switches the input of the
*1
DIGITAL LINK output supported device to the specified input.
Prioritizes brightness.
Operates the projector with low noise although the brightness
decreases compared to [NORMAL].
Controls the power with the setting set in [USER1].
Controls the power with the setting set in [USER2].
Controls the power with the setting set in [USER3].
Description
ENGLISH - 141
Advertisement
Table of Contents
