[System Selector] - Panasonic PT-RQ13K Operating Instructions Manual

[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[MANUAL INTENSITY]
(Manual light source
adjustment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
Note
f [LIGHTS OUT SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE].
f When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again
from the state that the light source has turned off by this function.
g When the brightness level of the video signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL]
g When the input signal is gone
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], it will take approximately 0.5 seconds to turn the light source back on
again from the state that the light source has turned off by this function.
f When [DYNAMIC GAMMA] is set to [3], the contrast will be maximized.
f The brightness control function and the dynamic contrast function will operate simultaneously, but the dynamic contrast function will not
operate while measuring the brightness and the color.

[SYSTEM SELECTOR]

The projector will automatically detect the input signal, but you can set the system method manually when an
unstable signal is input. Set the system method matching the input signal.
1) Press as to select [SYSTEM SELECTOR].
2) Press the <ENTER> button.
3) Press as to select a system format.
f Available system formats vary depending on the input signal.
Terminal
<DIGITAL LINK/LAN>
terminal, <HDMI IN 1>
terminal, <HDMI IN 2>
terminal, <HDMI IN 3>
terminal, <HDMI IN 4>
terminal
<DVI-D IN 1> terminal, <DVI-D
IN 2> terminal, <DVI-D IN
3> terminal, <DVI-D IN 4>
terminal
4) Press the <ENTER> button.
Note
f For details of the types of video signals that can be used with the projector, refer to "List of compatible signals" (x page 210).
f This may not function properly for some connected external devices.
f The selection item for the input signal to the <HDMI IN 1> terminal and the <HDMI IN 2> terminal can be selected when the optional
Interface Board equipped with the HDMI input is installed in <SLOT 1>.
f The selection item for the input signal to the <HDMI IN 3> terminal and the <HDMI IN 4> terminal can be selected when the optional
Interface Board equipped with the HDMI input is installed in <SLOT 2>.
f The selection item for the input signal to the <DVI-D IN 1> terminal and the <DVI-D IN 2> terminal can be selected when the optional
Interface Board equipped with the DVI-D input is installed in <SLOT 1>.
Chapter 4 Settings — [PICTURE] menu
Setting item
[DISABLE]
[0.0s] - [10.0s]
[0%] - [5%]
[0] - [255]
[OFF]
[1]
[2]
[3]
480i, 576i, 480p, or 576p
signal
Other moving image signals
480i, 576i, 480p, or 576p
signal
Other moving image signals
Details
Does not turn off the light source.
Turns off the light source when the brightness level of the video
signal being input goes under the value set in [LIGHTS OUT
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] -
[4.0s] can be selected in increments of 0.5.
Set the level of the brightness of the video signal to turn off the light
source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
Does not compensate the signal.
Slightly compensates the signal.
Moderately compensates the signal.
Strongly compensates the signal.
System format
Select [AUTO], [RGB], or [YC C
B
Select [AUTO], [RGB], or [YP P
B
Select [RGB] or [YC C ].
B R
Select [RGB] or [YP P ].
B R
].
R
].
R
ENGLISH - 87