Panasonic PT-RQ13K Operating Instructions Manual page 116

6) Press qw to switch the item.
f The items will switch each time you press the button.
[DEFAULT]
[USER]
f When [DEFAULT] is selected, proceed to Step 11).
7) Press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
8) Press asqw to select [RESOLUTION].
f Select [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p],
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], [1920x1200p],
[1920x2160p], [2048x1080p], or [2048x2160p].
9) Press the <ENTER> button.
f The [VERTICAL SCAN FREQUENCY] screen is displayed.
10) Press qw to select [VERTICAL SCAN FREQUENCY].
f Select [30Hz], [25Hz], or [24Hz] when [2048x2160p] or [1920x2160p] is selected for [RESOLUTION].
f Select [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [2048x1080p] or [1920x1080p] is selected for
[RESOLUTION].
f Select [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
f Select [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
g [2048x2160p], [1920x2160p], [2048x1080p], [1920x1080p], [1920x1080i]
11) Press the <ENTER> button.
f The confirmation screen is displayed.
12) Press qw to select [OK], and press the <ENTER> button.
Note
f The settings in [RESOLUTION] and [VERTICAL SCAN FREQUENCY] are displayed in [EDID STATUS].
f The resolution and vertical scanning frequency settings may also be required on your computer or video device.
f After configuring settings, your computer or video device or the projector may be required to be turned off and on.
f A signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video
device.
When the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed
To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the firmware version of
the 3G-SDI Terminal Board with Audio to be 2.00 or later. Consult your dealer regarding the version update to the
latest firmware if the version is earlier than 2.00.
For details on how to confirm the firmware version, refer to "How to confirm the firmware version of the 3G-SDI
Terminal Board with Audio" (x page 31).
Setting [SDI LINK] in [SLOT IN] (SDI input)
1) Press as to select [SLOT IN].
2) Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3) Press as to select [SDI LINK], and press the <ENTER> button.
f The [SDI LINK] screen is displayed.
4) Press as to select the setting.
[AUTO]
116 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Standard setting.
Set the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
Automatically selects the single link, the dual link, or the quad link.
The single link, dual link, or quad link is automatically distinguished by reading the payload ID
attached to each input signal. Single link will be selected when a payload ID is not added to the input
signal.
Quad link will be automatically selected when the optional 3G-SDI Terminal Board with Audio (Model
No.: TY-TBN03G) is installed in both of the slots.