Table of Contents
Advertisement
Page 16
22
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
24
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
3
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
25
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
3
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
26
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
8
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
DATA ENTRY
CS RECEIVER 1 FORMAT
blank(•)
Ademco Slow, Silent Knight Slow
1
Sescoa, Vertex, DCI, Franklin Fast
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
8
Radionics BFSK
27
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
do not program the first two digits of ANY User Code as the same digits entered for the "Ambush Prefix".
If the programmed code is less than 6 digits, press
Refer to the tables on the next page for the available User Option data entries.
X
GEM-P1664 Programming Instructions
Number of Keypads
Directly enter the total number of Keypads to be installed. Valid entries are from 01 to 07. Directly
enter the number of keypads, including leading zeros. Use number buttons
NOTE: Press
for a zero. Press
0
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including prefix letters, if
necessary, for receiver 1. Use number buttons
for a zero and
0
G 1
Pre-Dial Delay = "D"; Dial-Tone Detection = "E". Pressing
U
Press
to save. Press the NEXT/YES button to proceed. NOTE: Central Station Receiver 2 and
3 Telephone Numbers can only be entered in Direct Address Programming. See CS Receiver
Options.
Central Station Receiver 1 Account Number
Enter an account number of up to four digits. Use number buttons
1–9. NOTE: Press the
0
U
space (•). Press
to save. Press the NEXT/YES button to proceed. NOTE: Central Station
Receiver 2 and 3 Account Numbers can only be entered in Direct Address Programming. See CS
Reporting Options.
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number buttons
through
. NOTE: Press the
9
space (•). Press
G 1
save. Press the NEXT/YES button to proceed.
DATA ENTRY
9
0
B
C
D
E
Enter User Codes (Press the (
Enter up to 64 User Codes with User Options for each code. Refer to the tables below for available
data entries for User Options.
Press
once to set cursor to the User Number and enter the desired User Number. Press
R
once again to set the cursor to the User Code. Use the number buttons
R
enter a code from 3 to 6 digits. Enter up to 6 digits (4 digits are recommended) in the first six boxes
from left to right for each user code. Valid entries are: 0-9. Note: Press
spaces in between; leave blank (•) any trailing boxes. If an "Ambush Prefix" (Address 0495) is entered,
to set the cursor to USER OPTIONS.
R
U
to save. Press the NEXT/YES button to proceed.
through
1
through
G 5
button for a zero and press the
button for a zero and press
0
through
for letters B–E, respectively. Press
G 4
CS RECEIVER 1 FORMAT
FBI 4/3/1
Radionics Modem 2
SIA
Ademco Point ID
Ademco Express
Pager
) button to set cursor)
R
L
WI1423A 1/06
through
1
for digits 1–9; press
9
for letters B–F, respectively. NOTE:
will produce a blank space (•).
0
through
for digits
1
9
buttons for a blank
G 0
for a blank
G 0
NOTE: Modem IIe is available
only
in
Direct
Address
Programming. Central Station
Receiver 2 and 3 Formats can
only be entered in Direct
Address Programming. See
CS Receiver Options.
through
1
for a zero. No blank
0
NAPCO Security Systems
.
9
G
1
U
to
to
9
Advertisement
Table of Contents
