Drive Belt Tension; Drive Belt Installation - Meridian SEED TITAN 2SE Operator's Manual

Operator's Manual: Seed Titan
The Seed Titan™ 4SE conveyor is also driven by
a belt from the engine. The belt is tightened by
moving the engine base with the adjusting bolt.
IMPORTANT:
Always install and secure the
guard before resuming work.
b. Install the new belt and connect the two
ends together.
6. Tighten the two drive drum adjusting bolts
The instructions for the 4SE are the same as for
equally to 23 ft-lbs. While holding the
b. Install the new belt and connect the two
the 2SE:
adjusting bolt in place, retighten both locking
ends together.
1. Loosen the four engine mounting bolts (1).
nuts.
6. Tighten the two drive drum adjusting bolts
2. Loosen the engine base stabilizing bolt.
7. Start the conveyor to make sure the belt is
equally to 23 ft-lbs. While holding the
tracking properly. If the belt is not tracking
adjusting bolt in place, retighten both locking
3. Loosen the jam nut on engine base adjusting
properly, use the Belt Tracking Adjustment
nuts.
bolt (2).
procedure to correct the problem.
7. Start the conveyor to make sure the belt is
8. Recheck the tension and alignment of the
tracking properly. If the belt is not tracking
4. Move the engine base to set the desired belt
beltfrequentlyduringthefirsttenhoursof
properly, use the Belt Tracking Adjustment
tension.
operation and adjust, as needed.
procedure to correct the problem.
5. Tighten the jam nut.
Note: Then, resume regular maintenance.
8. Recheck the tension and alignment of the
Typically, a belt will seat itself during the
beltfrequentlyduringthefirsttenhoursof
6. Tighten the four engine mounting bolts.
firsttenhoursofoperationandthenrequire
operation and adjust, as needed.
less or no adjustment.
7. Tighten the engine base stabilizing bolt. Note: Then, resume regular maintenance.
Typically, a belt will seat itself during the
firsttenhoursofoperationandthenrequire
10.8 CONVEYOR DRIVE BELT
less or no adjustment.
The conveyor is driven by a belt from the motor.
The belt is tightened by moving the engine base
with the adjusting bolt.
10.8 CONVEYOR DRIVE BELT

10.8.1 Drive Belt Tension

The conveyor is driven by a belt from the motor.
The belt is tightened by moving the engine base
Release the base when replacing the belt. Always
with the adjusting bolt.
install and secure the guard before resuming work.
10.8.1 Drive Belt Tension
1. Loosen the four engine mounting bolts (1).
Release the base when replacing the belt. Always
install and secure the guard before resuming work.
1. Loosen the four engine mounting bolts (1).
4-8
2SE/4SE Box Seed Tender
™
10.8.1 Drive Belt Tension
Release the base when replacing the belt. Always
install and secure the guard before resuming work.
1. Loosen the four engine mounting bolts (1).
2. Loosen the engine base stabilizing bolt (2).
2. Loosen the engine base stabilizing bolt (2).
Fig 66 - Titan 4SE engine mount bolts
3. Loosen the jam nut on engine base adjusting
bolt (3) and move the engine base to set the
48
desired belt tension.
Fig 67 - Titan 4SE engine base stabilizing bolts
3. Loosen the jam nut on engine base adjusting
bolt (3) and move the engine base to set the
desired belt tension.
Fig 68 - 4SE engine base adjusting bolt
4. Tighten the jam nut.
5. Tighten the four engine mounting bolts.
6. Tighten the engine base stabilizing bolt.
4. Tighten the jam nut.
5. Tighten the four engine mounting bolts.

10.8.2 Drive Belt Installation

6. Tighten the engine base stabilizing bolt.
Use the following photo for the correct routing of
the drive belt. Always check the alignment of the
10.8.2 Drive Belt Installation
pulleys when replacing the belt.
Use the following photo for the correct routing of
the drive belt. Always check the alignment of the
pulleys when replacing the belt.
4. Tighten
5. Tighten
6. Tighten
10.8.2 Dr
Use the follo
the drive be
pulleys whe
Revised 02.2021