Alvarion BreezeACCESS VL System Manual page 259

MIB Parameter
*DFSChannelReuseOption
(*DFSChannelReuseParameters 1)
*DFSRadarActivityAssessmentPeriod
(*DFSChannelReuseParameters 2)
*DFSMaximumNumberOfDetectionsInAs
sessmentPeriod
(*DFSChannelReuseParameters 3)
*CountryCodeLearningBySU
(*FrequencyDefinition 12)
*CurrentAUOperatingFrequencyNew
(*FrequencyDefinition 13)
*AUDefinedFrequencyNew
(*FrequencyDefinition 14)
*AutoSubBandSelect
(*FrequencyDefinition 15)
*AutoSubBandSelectedFreqSubset
(*AutoSubBandSelect 1)
*AutoSubBandFrequencySubsetTable
(*AutoSubBandSelect 2)
*AutoSubBandFrequencySubsetEntry
(*AutoSubBandFrequencySubsetTable 1)
BreezeACCESS VL System Manual
Description
Applicable to AU/BU.
Enabling/disabling the DFS Channel
Reuse Algorithm.
Applicable to AU/BU.
The period in hours for assessment
of radar activity when the Channel
reuse algorithm is enabled.
Applicable to AU/BU. The maximum
number of radar detection in the
original channel during the Radar
Activity Assessment Period that is
required for reaching a decision to
try again the original channel.
Applicable to AU only. Starting with
4.0 it is nor applicable for
BreezeACCESS and BreezeNET B.
Defines whether the SU should learn
the country code of the AU.
Applicable to AU/BU. Read-only.
The operating frequency in MHz.
(Replaces
*CurrentAUOperatingFrequency to
support a resolution of 0.5 MHz for
units with HW revision C and
higher).
Applicable to AU/BU. Read-only. For
5.8 GHz products with SW version
below 2.0 this is the frequency in
MHz of the AU/BU after the next
reset.
For units with SW version 2.0 and up
this is the frequency in MHz to use
when the DFS Option is disabled.
(Replaces *AUDefinedFrequency to
support a resolution of 0.5 MHz for
units with HW revision C and
higher).
Auto Sub Band Select parameters.
Applicable to SU/RB with SW
version 4.0 and higher.
Applicable to SU/RB with SW
version 4.0 and higher. Apply the
selected subset. After the next reset
the new subset will be used for
scanning.
Applicable to SU/RB with SW
version 4.0 and higher. Not
accessible. The Frequency Subset
Table that includes all available sub-
bands and all the frequencies in
these sub-bands.
Applicable to SU/RB with SW
version 4.0 and higher. Not
accessible. An entry in the Auto
SubBand Frequency Subset Table.
breezeAccessVLMib
Value/Range
Integer
disable (1)
enable (2)
na (255)
Integer
1 – 12 hours.
Integer
1 – 10 detections.
Integer
disable (1)
enable (2)
na (255)
DisplayString
For 5.8 GHz products with
SW version below 2.0 the
range is 5740 to 5830 MHz
using a 10 MHz resolution.
For units with SW version
2.0 and up the range is as
defined in the selected Sub-
Band.
DisplayString
For 5.8 GHz products with
SW version below 2.0 the
range is 5740 to 5830 MHz
using a 10 MHz resolution.
For units with SW version
2.0 and up the range is as
defined in the selected Sub-
Band.
Integer
setAllSelectedFreqsSubset
(1),
cancel (2)
233